Увод
This manual provides essential instructions for the safe operation, maintenance, and storage of your Performance Tool W1611 2.25 Ton (4,500 lbs) Capacity Trolley Jack. Before using the jack, it is crucial to read and understand all instructions and safety warnings to prevent injury or property damage. Keep this manual for future reference.
Image: The Performance Tool W1611 2.25 Ton Trolley Jack, a yellow hydraulic jack with a long handle.
Важне информације о безбедности
WARNING: Failure to heed these warnings may result in personal injury or property damage.
- Прочитајте сва упутства: Understand the operation and limitations of the jack, as well as the hazards involved.
- Use on Hard, Level Surface: Always use the jack on a hard, level surface capable of supporting the load. Avoid soft ground or uneven surfaces.
- Do Not Exceed Rated Capacity: The W1611 jack has a maximum capacity of 2.25 tons (4,500 lbs). Do not attempt to lift loads heavier than this rating.
- Користите Џек постоља: This jack is a lifting device only. Immediately after lifting, support the vehicle with appropriate jack stands. Never work under a vehicle supported only by a jack.
- Center the Load: Ensure the load is centered on the jack saddle. Off-center loads can cause instability.
- Чувајте се: Keep hands, feet, and other body parts clear of moving parts and the area under the load.
- Проверите пре сваке употребе: Check the jack for any damage, leaks, or loose parts before each use. Do not use if damaged.
- Lower Slowly: Always lower the load slowly and in a controlled manner.
- Предлог 65 Упозорење: Овај производ може да садржи хемикалије за које је у држави Калифорнија познато да изазивају рак и урођене дефекте или другу репродуктивну штету. Оперите руке након руковања.
Садржај пакета
Проверите да ли су све компоненте присутне приликом распакивања:
- 1 Performance Tool W1611 2.25 Ton Trolley Jack
- 1 Operating Handle
- 1 Blow-molded plastic storage case
Спецификације
| Феатуре | Спецификација |
|---|---|
| Модел | В1611 |
| Капацитет оптерећења | 2.25 тоне (4,500 фунти) |
| Минимална висина подизања | 5-1/4 инча |
| Максимална висина подизања | 15 инча |
| Димензије производа (Д к Ш к В) | 23.2 к 10.3 к 6.8 инча |
| Тежина артикла | Approximately 27 lbs (including case) |
| Саддле | Steel lifting saddle with 360-degree swivel |
| Точкови | Heavy-duty steel front wheels, ball-bearing swivel rear wheels |
Слика: Крупни план view highlighting the steel lifting saddle and the heavy-duty wheels of the trolley jack.
Подешавање и почетна припрема
1. Распакивање
Carefully remove the trolley jack and its components from the packaging. Inspect for any shipping damage. If any damage is found, do not use the jack and contact customer support.
2. Склоп ручке
Insert the operating handle into the handle socket on the jack. Ensure it is securely seated. Some models may require tightening a set screw.
3. Bleeding the Hydraulic System
Before first use, or if the jack has been stored for an extended period, it is recommended to bleed any air from the hydraulic system to ensure proper operation. This procedure helps distribute fluid evenly through internal components.
- Locate the release valve (typically a screw or knob near the handle socket).
- Turn the release valve counter-clockwise to open it fully.
- Pump the handle vigorously six (6) to ten (10) times. This action will cycle the hydraulic fluid and expel any trapped air.
- Turn the release valve clockwise to close it firmly. The jack is now ready for use.
Упутство за употребу
1. Lifting a Vehicle
- Припремите возило: Park the vehicle on a hard, level surface. Engage the parking brake and place the transmission in 'Park' (automatic) or 'Reverse' (manual). Block the wheels that will remain on the ground to prevent movement.
- Поставите Јацк: Locate the manufacturer-recommended lifting points on your vehicle's frame or chassis. Position the jack so the saddle is directly under the lifting point. Ensure the jack is stable and the load is centered on the saddle.
- Подигните возило: Close the release valve by turning it clockwise until it is firm. Pump the operating handle up and down to raise the vehicle to the desired height.
- Обезбедите помоћу постоља за Џек: Once the vehicle is lifted, immediately place appropriately rated jack stands under the vehicle's designated support points. Slowly lower the vehicle onto the jack stands by gradually turning the release valve counter-clockwise. Ensure the vehicle is stable on the jack stands before performing any work.
2. Lowering a Vehicle
- Очистите област: Ensure all tools, personnel, and obstructions are clear from under and around the vehicle.
- Raise Slightly: If the vehicle is on jack stands, pump the jack handle a few times to lift the vehicle slightly off the jack stands.
- Remove Jack Stands: Carefully remove the jack stands from under the vehicle.
- Спустите возило: Slowly turn the release valve counter-clockwise to gradually lower the vehicle to the ground. Once fully lowered, remove the jack.
Image: The Performance Tool W1611 trolley jack positioned for lifting, demonstrating its extended handle and low profile.
Одржавање
Regular maintenance ensures the longevity and safe operation of your trolley jack.
- Чишћење: Keep the jack clean and free of dirt, grease, and debris. Wipe down the exterior with a clean cloth after each use.
- подмазивање: Periodically lubricate the pivot points, wheels, and especially the wheel castor bearings with light machine oil to ensure smooth operation and prevent rust.
- Хидраулична течност: Check the hydraulic fluid level periodically. If the fluid level is low, consult a qualified service technician for proper refilling with hydraulic jack oil. Do not use brake fluid or other non-specified fluids.
- инспекција: Regularly inspect the jack for any signs of wear, damage, or leaks. Pay close attention to welds, the hydraulic cylinder, and the handle. If any issues are found, discontinue use and have it repaired by a qualified professional.
Решавање проблема
Погледајте табелу испод за уобичајене проблеме и њихова могућа решења.
| Проблем | Могући узрок | Решење |
|---|---|---|
| Jack will not lift or lifts slowly | Ваздух у хидрауличном систему Низак ниво хидрауличке течности Отпусни вентил није потпуно затворен | Bleed the hydraulic system (refer to Setup section) Consult a qualified technician to check/refill fluid Ensure release valve is firmly closed clockwise |
| Jack lowers under load | Отпусни вентил није потпуно затворен Internal hydraulic leak Преоптерећење | Ensure release valve is firmly closed Discontinue use and consult a qualified technician Ensure load does not exceed 2.25 tons (4,500 lbs) |
| Jack is difficult to pump | Ваздух у хидрауличном систему Недостатак подмазивања на покретним деловима Damaged pump mechanism | Одзрачите хидраулични систем Lubricate pivot points and wheels Консултујте квалификованог техничара |
Складиштење
Proper storage helps maintain the jack's condition and readiness for use.
- Очистите пре складиштења: Ensure the jack is clean and dry before storing.
- Lower Ram Fully: Always lower the jack's ram completely before storage to relieve pressure on the hydraulic system.
- Користите футролу за складиштење: Store the jack in its provided blow-molded plastic case to protect it from dust, moisture, and damage. This also prevents it from rolling around if stored in a vehicle.
- Чувати на сувом месту: Store the jack in a dry, protected area, away from corrosive materials and extreme temperatures.
Image: The Performance Tool W1611 trolley jack alongside its durable black plastic storage case, emphasizing portability and protection.
Гаранција и подршка
For warranty information or technical support regarding your Performance Tool W1611 2.25 Ton Trolley Jack, please refer to the documentation included with your purchase or visit the official Performance Tool webсајту. Контакт подаци за корисничку подршку су обично доступни на сајту произвођача webсајт или паковање производа.
Можете посетити Продавница алата за перформансе на Амазону за више информација о производу и ресурсе за подршку.