TAMIYA JEEP WILLYS 1/4 TON 4X4

TAMIYA Jeep Willys 1/4 Ton 4X4 Hobby Model Kit Instruction Manual

Model: JEEP WILLYS 1/4 TON 4X4

1. Увод

This manual provides comprehensive instructions for the assembly of your TAMIYA 1/35 scale U.S. Willys MB Jeep 1/4-ton 4x4 Hobby Model Kit. Please read all instructions carefully before beginning assembly. This kit is designed for model enthusiasts and requires precision and attention to detail.

TAMIYA Jeep Willys MB 1/4-ton 4x4 Model Kit Box Art

Слика 1.1: Предња страна view of the TAMIYA Jeep Willys MB 1/4-ton 4x4 Model Kit box.

2. Безбедносне информације

WARNING: Contains small parts that could be a choking hazard. Not suitable for children under 3 years.

  • Always use tools with care. Sharp tools such as hobby knives and side cutters can cause injury if not handled properly.
  • Model cement and paints should be used in a well-ventilated area. Avoid inhaling fumes.
  • Keep all parts and tools out of reach of small children and pets.
  • Одложите отпадне материјале одговорно.

3. Садржај пакета

Your TAMIYA Jeep Willys MB 1/4-ton 4x4 Hobby Model Kit includes the following components:

  • Plastic sprues with all necessary parts for the Jeep assembly.
  • Clear parts for windshields and headlights.
  • Driver figure in a relaxed sitting pose.
  • Decal sheet with markings for five different vehicles.
  • Књижица са упутствима.
TAMIYA Jeep Willys MB Model Kit Box Contents

Слика 3.1: Готовоview of the kit contents inside the box.

TAMIYA Jeep Willys MB Model Kit Sprue Parts

Слика 3.2: Детаљно view of the plastic sprue parts included in the kit.

4. Потребан алат

The following tools are recommended for assembling your model kit:

  • Угаоне пинцете
  • Cutter-Knife
  • Decal-Scissors
  • Бочни секач
  • Paint Brush Set
  • Masking Tape (10mm with dispenser)
  • Plastic Cement (e.g., Tamiya Plastic Cement)
  • Decal Adhesive Soft/Haftmittel
Recommended Tools for TAMIYA Model Kit Assembly

Image 4.1: A selection of recommended tools for model assembly.

5. Упутство за монтажу

Follow the step-by-step diagrams in the included instruction booklet. General steps include:

  1. Carefully cut parts from the sprues using a side cutter.
  2. Clean any excess plastic (flash) from the parts with a hobby knife or sandpaper.
  3. Assemble sub-assemblies (e.g., engine, chassis, interior) as indicated.
  4. Use plastic cement sparingly to join parts. Allow sufficient drying time.
  5. Attach larger components to form the main structure of the Jeep.
  6. Install clear parts for windshields and headlights.
  7. Assemble and position the driver figure as desired.

Видео 5.1: Производ је преостаоview Video. This video provides a general look at the TAMIYA Jeep Willys model kit and its components, offering a visual introduction to the product before assembly.

6. Фарбање и наношење налепница

Refer to the included painting guide for recommended colors and placement. TAMIYA offers a range of acrylic and spray paints suitable for this model.

  • Наносите боју у танким, равномерним слојевима. Оставите сваки слој да се добро осуши пре наношења следећег.
  • Use masking tape to protect areas not intended for painting.
  • Cut decals carefully from the sheet. Dip them in water for a few seconds until they can slide off the backing paper.
  • Position decals on the model and gently press out any air bubbles or excess water. Use decal setting solutions for better adhesion and a painted-on look.
TAMIYA Jeep Willys MB Paint Guide

Слика 6.1: Примерample of a paint guide showing recommended TAMIYA paint colors for the model.

7. Приказивање вашег модела

Once assembled and painted, your TAMIYA Jeep Willys MB is ready for display. Consider placing it in a dust-free environment to preserve its finish. A display case can protect the model from dust and accidental damage.

8. Брига и излагање

To maintain the appearance of your model:

  • Dust regularly with a soft brush or compressed air.
  • Avoid direct sunlight, which can fade paint and decals over time.
  • Keep the model away from extreme temperature changes or high humidity.

9. Common Assembly Tips

  • Always dry-fit parts before applying cement to ensure a proper fit.
  • Use a small amount of cement to avoid damaging plastic surfaces.
  • For small parts, use tweezers for precise placement.
  • If a part does not fit easily, check for excess plastic or misalignment before forcing it.

10. Спецификације

ФеатуреДетаљ
БрандТАМИИА
Назив моделаJEEP WILLYS 1/4 TON 4X4
Скала1/35
Врста материјалаПластика
Број комада99
Димензије артикла (Д к Ш к В)10.25 к 6.25 к 1.5 инча
Тежина артикла0.1 килограма
Укључене компонентеModel Kit, Decals and Markings

11. Гаранција и подршка

This product is sold without an explicit warranty. For any questions regarding assembly or missing parts, please contact the manufacturer, MMD Holdings, or refer to the official TAMIYA webсајт за ресурсе подршке.