1. Увод
Thank you for choosing the Aqualine I50A-532 Brass Adjustable Impact Sprinkler. This manual provides essential information for the proper installation, operation, and maintenance of your sprinkler to ensure optimal performance and longevity. Please read these instructions carefully before use.
2. Производ је готовview
The Aqualine I50A-532 is a durable brass impact sprinkler designed for efficient and adjustable watering. It features a 1/2" MPT inlet connection and is constructed with high-quality brass, white bronze, and stainless steel components for reliability.
Слика 1: Aqualine I50A-532 Brass Adjustable Impact Sprinkler. This image displays the full assembly of the brass impact sprinkler, highlighting its robust construction and various adjustable components.
Кључне компоненте:
- Месингано тело: Обезбеђује издржљивост и отпорност на корозију.
- White Bronze Anti-Backsplash Arm: Ensures consistent rotation and prevents water from spraying backward.
- Stainless Steel Deflector Pin: Used for adjusting the spray pattern.
- Trip Sets: Mechanisms for setting the arc of rotation.
- овратник: Secures components and aids in adjustment.
- 1/2" MPT Inlet Connection: Standard male pipe thread for easy connection to irrigation systems.
3. Подешавање и инсталација
- Prepare Connection: Ensure your water supply line or riser has a compatible 1/2" FPT (Female Pipe Thread) connection.
- Нанесите заптивач за навоје: Wrap plumber's tape (PTFE tape) clockwise around the 1/2" MPT inlet threads of the sprinkler to ensure a watertight seal.
- Attach Sprinkler: Carefully thread the sprinkler onto the prepared connection. Hand-tighten first, then use a wrench to tighten an additional 1/2 to 1 full turn. Avoid over-tightening, which can damage threads.
- Позиционирање: Place the sprinkler in the desired location, ensuring it is upright and stable for optimal water distribution.
4. Упутство за употребу
The Aqualine I50A-532 sprinkler is designed for adjustable operation, allowing for both full-circle and partial-circle (arc) watering patterns.
Adjusting the Watering Arc:
- Full Circle Operation: To achieve a continuous 360-degree watering pattern, ensure the trip sets (arc adjustment clips) are disengaged or set to their widest position, allowing the sprinkler head to rotate freely.
- Partial Circle (Arc) Operation: The sprinkler can be adjusted to water an arc between 20 and 340 degrees. Locate the trip sets on the sprinkler head. By moving these clips, you can define the start and end points of the desired watering arc. The sprinkler arm will impact these clips, causing the head to reverse direction.
Water Pressure and Flow:
- Опсег радног притиска: The sprinkler operates optimally within a pressure range of 25 to 50 PSI (Pounds per Square Inch).
- Брзина протока: The flow rate varies between 2.6 and 5.0 GPM (Gallons Per Minute), depending on the installed nozzle size. This model is equipped with a 5/32" nozzle.
- Trajectory Angle: The water stream is projected at a 25-degree trajectory angle, reaching a highest point of approximately 5 feet above the nozzle level.
5. Одржавање
Regular maintenance ensures the longevity and efficient operation of your Aqualine impact sprinkler.
- Млазница за чишћење: Periodically check the nozzle for any debris or mineral buildup that might obstruct the water flow. Use a small, non-metallic tool to gently clear any blockages.
- подмазивање: The moving parts are designed for minimal maintenance. However, if rotation becomes stiff, a small amount of silicone-based lubricant can be applied to the pivot points, avoiding the nozzle opening.
- Зимљење: In freezing climates, disconnect the sprinkler from the water source and drain all water to prevent damage from ice expansion. Store in a dry, protected area.
- инспекција: Regularly inspect the sprinkler for any signs of wear, damage, or leaks. Replace worn components as necessary.
КСНУМКС. Решавање проблема
| Проблем | Могући узрок | Решење |
|---|---|---|
| Прскалица се не окреће | Low water pressure; Debris in nozzle or mechanism; Trip sets engaged for arc. | Check water pressure; Clean nozzle and mechanism; Ensure trip sets are disengaged for full circle. |
| Неравномерна расподела воде | Clogged nozzle; Incorrect deflector pin setting; Low water pressure. | Clean nozzle; Adjust deflector pin; Verify adequate water pressure. |
| Цурење воде из прикључка | Loose connection; Damaged threads; Insufficient thread sealant. | Tighten connection; Reapply thread sealant; Inspect threads for damage. |
7. Спецификације
| Феатуре | Детаљ |
|---|---|
| Модел | I50A-532 |
| Улазни прикључак | 1/2" MPT (Male Pipe Thread) |
| Материјали | Brass, White Bronze, Stainless Steel |
| Watering Arc | Adjustable from 20 to 340 degrees, or full 360 degrees |
| Trajectory Angle | 25 степени |
| Highest Stream Point | Approximately 5 ft. above nozzle level |
| Опсег радног притиска | 25 - 50 PSI |
| Flow Rate (with 5/32" nozzle) | 2.6 - 5.0 GPM |
| Nozzle Size (Included) | 5/32" |
| Димензије (Д к Ш к В) | 5 к 5 к 3 инча |
| Тежина артикла | 6.7 унци |
8. Гаранција и подршка
Aqualine products are manufactured to high-quality standards. For specific warranty information, please refer to the product packaging or contact Aqualine customer support directly.
If you encounter any issues or have questions regarding your Aqualine I50A-532 sprinkler, please visit the official Aqualine webсајт или контактирајте њихову службу за кориснике за помоћ.