Intermatic ET1105C 24-Hour Electronic Time Switch Instruction Manual

Увод

This manual provides instructions for the installation, operation, and maintenance of the Intermatic ET1105C 24-Hour Electronic Time Switch. This device is designed to control electrical loads with precise, programmable timing, offering an upgrade from mechanical time switches with features like up-to-the-minute programming, battery backup, and automatic daylight saving time corrections.

Важне информације о безбедности

УПОЗОРЕЊЕ: Опасност од пожара или електричног удара

• Код пластичних кућишта, спајање између цевних прикључака није аутоматско и мора се обезбедити као део инсталације.
• Ако се тачка за искључење напајања не види, закључајте је у ОФФ положају и tag то да спречи неочекивану примену моћи.
• Ensure there is no wire insulation under the terminal plate on the time switch connector. Firmly tighten terminal screws.
• Замените терминале који покривају пластични изолатор пре него што укључите напајање.
• ВРАТА ДРЖИТЕ ЗАТВОРЕНА СВЕ ВРЕМЕ када не сервисирате.

AVERTISSEMENT: Risque d'incendie ou de choc électrique

Pour les boîtiers en plastique, la liaison entre les raccordements de conduits n'est pas automatique et doit être prévue dans le cadre de l'installation.

Производ је завршенview

Image: Intermatic ET1105C Electronic Time Switch with its protective cover open, revealing the digital display, control buttons (MODE, RESET, ENTER/NEXT, ON/OFF, +, -), and the wiring terminal block at the bottom. The internal wiring diagram and specifications are visible on the left panel.

The Intermatic ET1105C is an electronic 24-hour time switch designed for direct control of loads up to 30 amps resistive or inductive, and tungsten loads. It features battery-powered carryover for program retention during power outagес.

Цонтрол Панел

• Дугме МОДЕ: Cycles through programming menus.
• Ресет: Clears memory.
• ENTER/NEXT Button: Confirms selections and advances to the next step.
• Дугме за укључивање/искључивање: Manually turns the load ON or OFF, or toggles events.
• + / - Дугмад: Adjusts values (date, time, event settings).
• ЛЦД екран: Shows current time, date, program status, and load status.

Инсталација

Волtagе Избор

The ET1105C supports multi-volt operation from 120 to 277 VAC, 50/60 Hz. Refer to the internal instruction manual or wiring diagram for specific voltage selection procedures.

Ожичење

Wiring should be performed by a qualified electrician in accordance with all local and national electrical codes.

1. Уверите се да је сва струја искључена на главном прекидачу пре почетка инсталације.
2. Mount the time switch securely in the desired location.
3. Спојите жице за напајање на предвиђене терминале.
4. Connect the load wires to the appropriate output terminals.
5. Ensure all terminal screws are firmly tightened and no wire insulation is caught under the terminal plate.
6. Replace the plastic insulator covering the terminals before restoring power.

Refer to the wiring diagram printed on the inside of the enclosure for detailed connection instructions.

Упутство за употребу

Ручни ОН/ОФФ рад

In either AUTO or MANUAL mode, press the ОН/ОФФ button to manually toggle the load. The display will indicate if the load is currently ON or OFF.

Кораци програмирања

The time switch allows for up to 28 events (14 ON / 14 OFF).

1. Приступ менијима: Притисните тастер МОДЕ button repeatedly to cycle through the programming menus (DATE, TIME, ON/OFF EVENTS).
2. Датум подешавања: When "SET DATE" appears, use the + or - keys to enter the current date. Press ЕНТЕР потврдити.
3. Време подешавања: When "SET CLOCK" appears, use the + or - keys to enter the current time. Press ЕНТЕР потврдити.
4. Setting ON/OFF Events: When "ON/OFF EVENTS" appears, press the + or - button. The display will show "12:00 AM" with the load status (ON/@) and event number. Use the + or - keys to set the desired ON or OFF time and day(s) for the event. Press the ОН/ОФФ load button to toggle the load status (ON or OFF). To clear an event, select "(nil)". Press ЕНТЕР to save the event and move to the next event, or press МОДЕ to advance to AUTO run mode.

Аутоматски режим (АУТО)

Притисните тастер МОДЕ button repeatedly until "AUTO" appears on the display. In AUTO mode, the time switch will execute the programmed ON/OFF events. Manual overrides using the ОН/ОФФ load button are temporary and will revert to the programmed schedule at the next event.

Уређивање и Реviewинг Догађаји

Events can be edited or reviewed by returning to the appropriate menu using the МОДЕ дугме.

Одржавање

Замена батерије

The time switch uses two industrial-grade AAA standard non-rechargeable 1.5-volt alkaline batteries for program retention.

1. To replace the battery, locate the battery tray.
2. Pull the battery tray out and downward to remove the battery holder.
3. Замените батерије, поштујући исправан поларитет.
4. The batteries should be replaced approximately every 3 years after installation.

Спецификације

Гаранција

This product comes with a 1-year limited warranty. For detailed warranty information and claims, please contact Intermatic customer support.

Подршка

For technical assistance, troubleshooting, or further information, please visit the official Intermatic webсајту или се обратите њиховом одељењу за корисничку подршку.

Intermatic Incorporated, Spring Grove, Illinois 60081-9698