Westek TMDCD60 Hardwire Indoor Countdown 6-Setting Wall Switch Timer User Manual

Увод

The Westek TMDCD60 is a hardwire indoor countdown timer designed to replace a standard wall switch. It provides timed control for lights, fans, heaters, and other devices, automatically turning them off after a selected duration. This manual provides instructions for safe installation, operation, and maintenance of your timer switch.

Безбедносне информације

УПОЗОРЕЊЕ: Опасност од струјног удара. Improper installation can lead to serious injury or death. Always turn off power at the circuit breaker or fuse box before beginning installation. Consult a qualified electrician if you are unsure about any part of the installation process.

• Овај уређај је само за унутрашњу употребу.
• Уверите се да су сви прикључци ожичења безбедни и да су у складу са локалним електричним прописима.
• Do not exceed the electrical ratings of the device.
• A neutral wire is required for installation. Older homes may not have a neutral wire in the switch box.

Садржај пакета

• Westek TMDCD60 Countdown Timer Switch
• Упутство за употребу (овај документ)

Производ је завршенview

The Westek TMDCD60 timer switch features a single push-button control and LED indicators for selected time settings. It is designed to fit into a standard wall switch box and can be used with a standard rocker wallplate (not included).

Слика 1: Предња страна view of the TMDCD60 timer switch. The face includes a single control button and five LED indicators labeled "10 MIN", "20 MIN", "30 MIN", "60 MIN", and "HOLD".

Инсталација

1. Искључите напајање: Locate the circuit breaker or fuse that controls the switch you are replacing. Turn off the power completely before proceeding. Verify power is off using a voltagе тестер.
2. Уклоните постојећи прекидач: Carefully remove the wallplate and unscrew the existing switch from the wall box. Disconnect the wires from the old switch. Note the connections for reference.
3. Идентификујте жице: The Westek TMDCD60 timer requires four wires:
   • Црна жица: Hot (Line)
   • Црвена жица: Load (to the device being controlled)
   • Бела жица: Неутрално
   • зелена жица: Гроунд

   Ensure your wall box contains a neutral wire. If not, this timer cannot be installed without running a new neutral wire, which should be done by a qualified electrician.

   

   Слика 2: Позади view of the TMDCD60, illustrating the labeled wires for proper connection.
4. Повежите жице: Using wire nuts (not included), connect the wires from the wall box to the corresponding wires on the TMDCD60 timer switch:
   • Повежите Црно wire from the timer to the Hot (Line) жицу из зидне кутије.
   • Повежите Црвени wire from the timer to the Учитај wire from the wall box (to the light/fan).
   • Повежите Бела wire from the timer to the Неутрално жицу из зидне кутије.
   • Повежите Зелена wire from the timer to the Гроунд жицу из зидне кутије.
5. Монтирајте тајмер: Carefully fold the wires into the wall box. The timer is deeper than a standard switch, so ensure there is enough space. Secure the timer switch to the wall box using the provided screws.
6. Инсталирајте зидну плочу: Attach a standard rocker wallplate (not included) over the timer switch.
7. Врати снагу: Поново укључите напајање на прекидачу или кутији са осигурачима.

Операција

The TMDCD60 timer operates with a single push-button control. Each press cycles through the available countdown settings and the HOLD function.

1. Turning On and Setting Timer: Press the control button once to activate the timer. The timer will cycle through the following settings with each subsequent press:
   • OFF (no LED lit)
   • 10 Minutes (10 MIN LED lights up)
   • 20 Minutes (20 MIN LED lights up)
   • 30 Minutes (30 MIN LED lights up)
   • 60 Minutes (60 MIN LED lights up)
   • HOLD (HOLD LED lights up)

   The connected device will remain on for the selected duration and then automatically turn off. The corresponding LED will indicate the active setting.

2. ХОЛД функција: To keep the connected device on indefinitely, press and hold the control button for approximately one second until the "HOLD" LED illuminates. In HOLD mode, the device will remain on until you press the button again to turn it off or select a countdown setting.
3. Искључивање: To turn off the connected device before the countdown finishes or while in HOLD mode, press the control button until no LEDs are lit.

Одржавање

The Westek TMDCD60 timer switch requires minimal maintenance. To clean the surface, wipe with a soft, damp крпа. Не користите абразивна средства за чишћење или раствараче. Уверите се да је напајање искључено пре чишћења.

Решавање проблема

Спецификације

• Модел: TMDCD60
• Бренд: Вестек
• Боја: Бела
• Улазни волtage: КСНУМКСВ АЦ КСНУМКСХз
• Максимално оптерећење: 15A Resistive, 1000W Tungsten, 500VA Ballast, 1/4 HP Motor
• Подешавања тајмера: 10, 20, 30, 60 minutes, HOLD
• Димензије: 1"D x 1"W x 1"H (Note: These dimensions typically refer to packaging; the device itself is deeper for in-wall installation.)
• Тежина артикла: 4.48 унци
• Тип монтаже: зид
• Стил промене: Роцкер Свитцх
• Неутрална жица: Обавезно

Гаранција и подршка

Овај Вестеков производ је покривен 1-годишња ограничена гаранција од дана куповине. Ова гаранција покрива недостатке у материјалу и изради при нормалној употреби.

For technical support or warranty claims, please contact Westek customer service. You can find more information and contact details on the official Westek webсајту или посетом Вестек продавница на Амазону.