Увод
The OSD Audio AB12 is an in-wall speaker selector A/B switch designed to manage audio output between two amplifiers and one pair of speakers, or one amplifier and two pairs of speakers. This device allows for convenient selection of audio sources or destinations within a dedicated audio zone. It is rated for up to 100 watts per channel and features a push-button control for easy operation.
Мере предострожности
- Увек искључите напајање са amplifier and any connected audio equipment before installation or wiring.
- Ensure all wiring connections are secure to prevent short circuits or damage to equipment.
- Do not exceed the maximum power rating of 100 watts per channel.
- Consult a qualified electrician if you are unsure about any electrical wiring procedures.
Подешавање и инсталација
Алати су потребни
- Одвијач (Пхиллипс глава)
- Жице стриптизета
- Електрична трака (опционално)
- Standard single-gang junction box (if not already installed)
Упутства за ожичење
The AB12 features removable, solderless terminals for easy wiring. It accepts speaker wire up to 14 gauge. For optimal sound quality, 14-16 gauge wire is recommended.
- Припремите жице: Strip approximately 1/4 to 1/2 inch of insulation from the ends of your speaker wires. Twist the bare wire strands tightly.
- Идентификујте терминале: The AB12 has clearly labeled terminals for 'OUTPUT' (to speakers) and 'AMP A INPUT' / 'AMP B INPUT' (from amplifiers). Each input/output has terminals for Left (+) and (-), and Right (+) and (-).
- Повежите звучнике: Connect your speaker wires to the 'OUTPUT' terminals. Ensure correct polarity (positive to positive, negative to negative).
- Повежите се Ampослободиоци: Connect the speaker output wires from your primary amplifier to the 'AMP A INPUT' terminals. Connect the speaker output wires from your secondary amplifier (if used) to the 'AMP B INPUT' terminals. Maintain correct polarity.
Слика 1: Задња страна view of the AB12 switch with clearly labeled input and output terminals for wiring.
Слика 2: Прample of speaker wire connections to the removable solderless terminals.
Монтажа прекидача
The AB12 is designed to fit into a standard single-gang junction box with a minimum depth of 2.9 inches. The dimensions of the selector are approximately 1 inch (W) x 2.75 inches (H) x 1.75 inches (D).
- Припремите разводну кутију: Ensure the junction box is securely installed in the wall.
- Insert Switch: Carefully push the wired AB12 switch into the junction box. Ensure wires are not pinched.
- Сигурна предња плоча: Attach the desired color faceplate (white, beige, or light almond options are typically included) over the switch and secure it to the junction box using the provided screws.
Figure 3: Mounting brackets for securing the switch within a standard gang box.
Figure 4: The AB12 switch typically includes multiple faceplate colors for aesthetic integration.
Упутство за употребу
The OSD Audio AB12 switch provides a simple push-button mechanism to select between two audio configurations.
Функционалност
- Два Amplifiers to One Speaker Pair: Повежите два amplifiers to 'AMP A INPUT' and 'AMP B INPUT' respectively. Connect one pair of speakers to 'OUTPUT'. Press the button to switch between Amplifier A and Amplifier B playing through the single speaker pair.
- Један Amplifier to Two Speaker Pairs: Повежите један amplifier to 'AMP A INPUT'. Connect two pairs of speakers to 'OUTPUT' (one pair wired to the 'A' side of the output terminals, the other to the 'B' side, if applicable, or use the switch to select between two distinct output paths). Press the button to switch between Speaker Pair A and Speaker Pair B playing from the single ampлифиер.
The switch is designed to allow power to flow to speakers from either A or B, but not from both simultaneously. This prevents potential damage to amplifiers or speakers due to conflicting signals.
Figure 5: The AB12 switch integrated into an audio system, allowing selection between different sources or destinations.
Одржавање
The OSD Audio AB12 In-Wall Speaker Selector requires minimal maintenance.
- Чишћење: To clean the faceplate, gently wipe it with a soft, dry cloth. Avoid using abrasive cleaners or solvents, as these can damage the finish.
- Везе: Periodically check all wiring connections to ensure they remain secure. Loose connections can lead to signal loss or poor audio quality.
- Окружење: Ensure the switch is installed in a dry environment, away from excessive heat or moisture.
Решавање проблема
If you encounter issues with your AB12 speaker selector, refer to the following troubleshooting steps:
| Проблем | Могући узрок | Решење |
|---|---|---|
| Нема звука из звучника | Лабаве везе ожичења Нетачан положај прекидача Amplifier or speaker issue | Check all speaker wire connections at the AB12 switch and at the amplifier/speakers. Ensure the switch is fully engaged in the desired A or B position. Verify amplifier and speakers are functioning correctly by bypassing the switch temporarily. |
| Sound from only one speaker (left or right channel) | Нетачан поларитет ожичења Loose connection for one channel Неисправан механизам прекидача | Verify correct positive (+) and negative (-) wiring for both left and right channels. Check connections for the affected channel. If the issue persists, the internal switch mechanism may be faulty; contact support. |
| Difficulty fitting into standard gang box | Insufficient depth or width in junction box Excessive wiring inside box | Ensure the junction box meets the minimum depth requirement (2.9 inches). Carefully arrange wires to minimize bulk. Some older or non-standard boxes may require minor modification (e.g., widening the opening) or a deeper box. |
| Distorted or poor audio quality | Incorrect wire gauge Лабаве везе Exceeding power rating | Use recommended 14-16 gauge speaker wire. Check all connections. Ensure the amplifier output does not exceed the 100-watt rating of the switch. |
Спецификације
| Феатуре | Спецификација |
|---|---|
| Модел | АБ12 |
| Оперативни режим | А/Б прекидач |
| Повер Ратинг | 100 вати по каналу |
| Фреквенцијски одзив | 20Хз до 20КХз |
| Мерач жице звучника | Up to 14 gauge (14-16 gauge recommended) |
| Тип конектора | Терминали без лемљења |
| Ацтуатор Типе | Притисните дугме |
| Број позиција | 2 |
| Тип монтаже | Standard Single-Gang Box Mount |
| Димензије производа (Д к Ш к В) | 4.5 к 2.75 к 2.5 инча |
| Тежина артикла | 6.4 унци |
| Материјал (кућиште) | Пластика |
| Контакт материјал | Метал |
| Боја | White (with additional faceplate options) |
Гаранција и подршка
OSD Audio products are designed for reliability and performance. For warranty information or technical support, please refer to the official OSD Audio webсајт или контактирајте њихову службу за кориснике. Сачувајте рачун као доказ о куповини за евентуалне рекламације по гаранцији.
Подршка на мрежи: ввв.осдаудио.цом