1. Увод
Thank you for choosing the Legrand 077014 Mosaic Pull Cord Switch. This product is designed for reliable control of lighting or other electrical circuits. It features a 2-module design, rated for 10AX and 250V, and comes in a white finish. This manual provides essential information for the safe installation, operation, and maintenance of your switch.
Image of the Legrand 077014 Mosaic Pull Cord Switch, showing its white finish and pull cord mechanism.
2. Безбедносне информације
УПОЗОРЕЊЕ: Electrical installation should only be performed by a qualified electrician. Failure to follow these instructions can result in electric shock, fire, or serious injury.
- Always disconnect power at the main circuit breaker or fuse box before attempting any electrical work.
- Проверите да ли је напајање искључено помоћу волtagе тестер пре него што додирнете било коју жицу.
- Уверите се да су сви прикључци ожичења безбедни и да су у складу са локалним електричним прописима.
- Немојте прекорачити наведену волtage (250V) or current (10A) ratings of the switch.
- Држите производ даље од воде и влаге.
- Овај производ је намењен само за унутрашњу употребу.
3. Садржај пакета
Молимо вас да проверите пакет за следеће ставке:
- 1 x Legrand 077014 Mosaic Pull Cord Switch
- 1 x Cord (approximately 1.5 meters in length)
4. Инсталација
This section provides general guidance for installing the Legrand 077014 Pull Cord Switch. For detailed wiring diagrams and specific installation requirements, consult a qualified electrician and refer to local electrical codes.
4.1 Припрема
- Искључите напајање: Turn off the power supply to the circuit at the main breaker.
- Проверите искључење напајања: Користите волtage tester to confirm that the power is completely off at the installation site.
- Сакупите алате: You will need basic electrical tools such as screwdrivers, wire strippers, and a voltagе тестер.
4.2 Wiring the Switch
The Legrand 077014 is a two-way (va-et-vient) switch, meaning it can control a light from two different locations when paired with another two-way switch. If used as a simple on/off switch, only two terminals are typically used.
- Identify the live (phase), neutral, and load wires.
- Connect the incoming live wire to the common terminal of the switch.
- Connect the outgoing wire to the light fixture (load) to one of the switching terminals.
- If used as a two-way switch, connect the traveler wires between this switch and the other two-way switch.
- Уверите се да су све везе чврсте и безбедне.
4.3 Монтажа прекидача
- Carefully place the wired switch into the flush-mounted box or surface-mounted enclosure.
- Secure the switch using the provided screws.
- Attach the cover plate (if applicable) and ensure it is flush with the wall surface.
4.4 Завршних корака
- Врати снагу: Поново укључите напајање на главном прекидачу.
- Тест функционалност: Test the switch by pulling the cord to ensure it operates correctly.
5. Упутство за употребу
The Legrand 077014 Pull Cord Switch is simple to operate:
- To turn on the connected device (e.g., light), gently pull the cord downwards until you hear a click.
- To turn off the connected device, gently pull the cord downwards again until you hear a click.
- The switch operates in an alternating fashion: one pull for ON, the next pull for OFF.
6. Одржавање
To ensure the longevity and proper functioning of your Legrand 077014 Pull Cord Switch, follow these simple maintenance guidelines:
- Чишћење: Disconnect power before cleaning. Use a soft, dry cloth to wipe the surface of the switch. Do not use abrasive cleaners, solvents, or excessive moisture, as these can damage the finish or internal components.
- инспекција: Periodically check the cord for any signs of wear, fraying, or damage. If the cord is damaged, it should be replaced by a qualified technician.
- Avoid Over-pulling: Do not pull the cord with excessive force, as this can damage the internal mechanism.
КСНУМКС. Решавање проблема
If you encounter issues with your Legrand 077014 Pull Cord Switch, refer to the table below:
| Проблем | Могући узрок | Решење |
|---|---|---|
| Switch does not operate (no light/power) | No power to the circuit; Loose wiring connection; Faulty bulb/device; Internal switch failure. | Check circuit breaker/fuse. Verify all wiring connections are secure (power off). Test bulb/device. If issues persist, consult a qualified electrician. |
| Cord is stuck or difficult to pull | Блокада или оштећење унутрашњег механизма. | Do not force the cord. Disconnect power and inspect for visible obstructions. If damaged, replace the switch or consult a qualified electrician. |
| Switch makes unusual noises | Internal component wear or damage. | Disconnect power immediately. This may indicate an internal fault. Replace the switch or consult a qualified electrician. |
If you are unable to resolve the issue after following these steps, please contact Legrand customer support or a qualified electrician.
8. Спецификације
| Феатуре | Спецификација |
|---|---|
| Број модела | 077014 |
| Тип | Pull Cord Switch (Two-way / Va-et-vient) |
| Модули | 2 модула |
| Називна струја | 10 АКС |
| Ратед Волtage | 250 В |
| Боја | Бела |
| Материјал | Пластика |
| Димензије производа (Д к Ш к В) | 9.7 к 9.7 к 5.7 цм |
| Тежина | 40 грама |
| Дужина кабла | 1.5 м |
| Усклађене спецификације | NF |
| Земља порекла | Немачка |
9. Гаранција и подршка
Legrand products are manufactured to high-quality standards. For information regarding product warranty, please refer to the terms and conditions provided at the point of purchase or visit the official Legrand website. For technical support, spare parts, or further assistance, please contact Legrand customer service through their official channels.
Молимо да сачувате ово упутство за будућу употребу.