Voltcraft DVM230W

VOLTCRAFT DVM230W Digital Installation Meter Module

Упутство за употребу

1. Увод

This manual provides essential information for the safe and effective use of your VOLTCRAFT DVM230W Digital Installation Meter Module. This module is designed for integration into laboratory devices and control panels, offering precise digital measurements with a clear white backlight display. Please read these instructions thoroughly before installation and operation.

2. Безбедносне информације

  • Always ensure the power supply is disconnected before installing or servicing the module.
  • This device is intended for professional installation. Incorrect installation can lead to damage or injury.
  • Do not expose the module to moisture, extreme temperatures, or corrosive environments.
  • Only use the module within its specified electrical parameters.
  • Refer to local electrical codes and regulations for proper installation procedures.

3. Производ је готовview

The VOLTCRAFT DVM230W is a compact digital meter module featuring a 10 mm digit height and a white backlight for enhanced readability. It is designed for recessed mounting with standard DIN dimensions.

Кључне карактеристике:

  • Recessed installation dimensions: 45 x 22 mm
  • Module with DIN dimensions 48 x 24 mm
  • 10 mm digit height
  • White LED backlight for visibility in low light conditions
  • Battery wear indicator
  • Функција задржавања података
  • Display of units: °C, °F, V, A, μ, m, M, k, ohms
  • Улазни отпор: 100 МΩ
  • Measurement range extendable via external resistors (voltage splitter, shunt)

Компоненте производа:

Фронт view of the VOLTCRAFT DVM230W Digital Installation Meter Module displaying '1.305 mV'

Слика 3.1: Предња страна View
This image shows the front of the DVM230W module with its digital display active, showing a reading of '1.305 mV'. The white backlight is visible, enhancing the clarity of the digits and unit indicators.

Позади view of the VOLTCRAFT DVM230W Digital Installation Meter Module showing the circuit board and connection pins

Слика 3.2: Задња страна View (Circuit Board)
This image displays the rear of the DVM230W module, revealing the internal circuit board with various electronic components, including resistors (RA, RB), capacitors, and the connection pins for integration into a system. The transparent casing allows visibility of the internal electronics.

Сиде view of the VOLTCRAFT DVM230W Digital Installation Meter Module, showing its compact form factor and transparent casing

Слика 3.3: Страна View
Ова слика представља споредног професионалцаfile of the DVM230W module, highlighting its compact and rectangular form factor. The transparent casing on the sides allows a partial view of the internal components and the 'VOLTCRAFT DVM 230W' branding on the side label.

4. Подешавање и инсталација

The DVM230W module is designed for recessed mounting. Ensure the mounting surface has an opening of 45 x 22 mm.

  1. Монтажа: Carefully insert the module into the prepared opening. The module is designed to snap into place. Ensure a snug fit to prevent movement. If the fit is too tight, minor adjustments to the opening or the use of a small amount of adhesive may be necessary.
  2. Електричне везе: Connect the module to the male bars of your system. Refer to the wiring diagram provided with your specific application for correct polarity and signal connections.
  3. Extending Measurement Range (Optional): За мерење волtages or currents beyond the module's default range (e.g., 0-200 mV), external resistors (voltage splitter for voltage, shunt for current) must be connected in series.
  4. Internal Configuration for Extended Range: If extending the measurement range, it is crucial to remove the 0 Ohm SMD resistor at position RA on the circuit board. Failure to do so before installing a voltage divider or shunt can damage the device. Consult the detailed circuit diagram for precise location of RA.
  5. Unit and Decimal Adjustment: The module allows for adjustment of displayed units and decimal places. This is typically done via solder bridges or pin headers on the circuit board. Refer to the detailed internal diagram for specific configuration points.

5. Упутство за употребу

Once installed and powered, the DVM230W module will display the measured value on its digital screen.

  • Читање екрана: The 10 mm digits provide clear readings. The white backlight ensures visibility in various lighting conditions.
  • Индикација јединице: The display will show the configured unit (e.g., V, mV, A, mA, Ohms, kOhms, MOhms, °C, °F) alongside the numerical value.
  • Функција чувања података: If equipped with a data-hold feature (check your specific model's pinout/buttons), activate it to freeze the current reading on the display.
  • Battery Wear Indicator: The module includes a battery wear indicator. If this indicator activates, it suggests the internal power source (if applicable) or the external power supply is insufficient or failing.

6. Одржавање

The VOLTCRAFT DVM230W module requires minimal maintenance.

  • Чишћење: Користите меку, суву крпу за чишћење екрана и цasing. Do not use abrasive cleaners or solvents, as these can damage the plastic and display.
  • инспекција: Periodically inspect the connections for any signs of corrosion or loose wiring.
  • Услови животне средине: Ensure the module operates within its specified temperature and humidity ranges to prolong its lifespan.

КСНУМКС. Решавање проблема

  • Нема приказа/нетачно очитавање:
    • Check power supply connections and ensure correct voltage.
    • Verify input signal connections for correct polarity and range.
    • If using an extended measurement range, confirm that the 0 Ohm SMD resistor at RA was correctly removed before installing external resistors. Incorrect configuration here can lead to erroneous readings or damage.
  • Трепери екран:
    • Check for unstable power supply.
    • Ensure proper grounding to minimize electrical interference.
  • Battery Wear Indicator Active:
    • If the module uses an internal battery, replace it.
    • If powered externally, check the stability and voltage of the external power source.

8. Спецификације

ФеатуреСпецификација
Број моделаDVM230W (Manufacturer Part Number: 126567)
Монтажне димензије45 к 22 мм
Module Dimensions (DIN)48 к 24 мм
Висина цифара10 мм
Позадинско осветљењеБела ЛЕД
Инпут Ресистанце100 МΩ
Извор напајањаHand-operated (implies external power supply, not self-contained)
Тежина артикла0.32 унци
Димензије пакета4.45 к 2.01 к 1.26 инча
Датум првог доступног19. септембра 2014. године

9. Гаранција и подршка

For warranty information and technical support, please refer to the documentation provided at the time of purchase or visit the official Voltcraft webсајт. Конкретни гарантни услови могу се разликовати у зависности од региона и продавца.

Такође можете посетити Voltcraft Store on Amazon за додатне информације о производу и ресурсе за подршку.

© 2023 VOLTCRAFT. Сва права задржана.