PerTronix Flame-Thrower Electronic Ignition Distributor User Manual

1. Увод

This manual provides comprehensive instructions for the installation, operation, maintenance, and troubleshooting of your PerTronix Flame-Thrower Electronic Ignition Distributor (Model D134600). This distributor is designed to provide enhanced ignition performance for compatible Ford Small Block engines, featuring integrated Ignitor electronic ignition technology for improved reliability and power.

Молимо вас да пажљиво прочитате ово упутство пре инсталације и рада како бисте осигурали правилно функционисање и безбедност.

2. Безбедносне информације

Увек се придржавајте следећих мера предострожности:

• Искључите акумулатор возила пре него што извршите било какве електричне радове.
• Носите одговарајућу личну заштитну опрему (ЛЗО), укључујући заштитне наочаре и рукавице.
• Ensure the engine is cool before working on ignition components.
• Keep ignition components away from flammable materials.
• Consult a qualified mechanic if you are unsure about any installation steps.
• Овај производ садржи хемикалије за које је у држави Калифорнија познато да изазивају рак и урођене дефекте или другу репродуктивну штету. Оперите руке након руковања.

3. Шта је у кутији

Пре почетка инсталације проверите да ли су све компоненте присутне:

• PerTronix Flame-Thrower Electronic Ignition Distributor (Model D134600)
• Distributor Cap
• Ротор
• Упутства за инсталацију (ово упутство)

Image: PerTronix Flame-Thrower Electronic Ignition Distributor with cap, rotor, and wiring visible.

4. Подешавање и инсталација

Правилна инсталација је кључна за оптималне перформансе. Пажљиво пратите ове кораке:

1. Припрема:
   • Одвојите негативни кабл батерије.
   • Mark the position of the rotor on the old distributor relative to the distributor body, and the position of the distributor body relative to the engine block. This will help with re-timing.
   • Label all spark plug wires before removal.
2. Old Distributor Removal:
   • Remove the distributor cap and spark plug wires.
   • Disconnect any electrical connections to the old distributor.
   • Loosen the distributor hold-down clamp and carefully lift the old distributor out of the engine block. Note the rotation of the rotor as it comes out.
3. New Distributor Installation:
   • Ensure the engine is at Top Dead Center (TDC) on the compression stroke for cylinder #1.
   • Align the new PerTronix distributor's gear with the camshaft gear. The rotor should point to the #1 spark plug terminal on the cap when fully seated. You may need to slightly rotate the rotor or the oil pump drive shaft to engage the gears.
   • Once seated, ensure the distributor body is oriented correctly as marked during removal.
   • Secure the distributor with the hold-down clamp, but do not fully tighten yet to allow for timing adjustments.
4. Ожичење:
   • The PerTronix Ignitor module has two wires: a red wire and a black wire.
   • Повежите црвена жица to a switched 12-volt power source that is active when the ignition is in the "ON" and "START" positions. This must be a full 12V source, not a resisted wire.
   • Повежите црна жица to the negative (-) terminal of the ignition coil.
   • Ensure all connections are clean and secure.
5. Final Assembly and Timing:
   • Install the new distributor cap and reattach the spark plug wires in the correct firing order.
   • Поново повежите негативни кабл батерије.
   • Start the engine and use a timing light to set the ignition timing according to your vehicle's specifications.
   • Once timing is set, fully tighten the distributor hold-down clamp.

Слика: прamples of Flame-Thrower distributors, illustrating the "Stock Look" and "Billet Plug n' Play" designs. The D134600 is a "Stock Look" model.

5. Упутство за употребу

The PerTronix Flame-Thrower Electronic Ignition Distributor operates automatically once installed and timed correctly. It replaces traditional points and condenser systems with a maintenance-free electronic module.

• The integrated Ignitor system delivers a consistent, high-energy spark to the spark plugs, improving combustion efficiency.
• The precision timing control ensures stable engine performance across all RPM ranges.
• No adjustments are required for the electronic ignition system itself after initial timing.

6. Одржавање

The PerTronix Flame-Thrower Electronic Ignition Distributor is designed for minimal maintenance. Unlike traditional points systems, there are no points to adjust or replace.

• Редовна инспекција: Periodically inspect the distributor cap and rotor for cracks, carbon tracking, or excessive wear. Replace if necessary.
• Ожичење: Check all electrical connections for tightness and corrosion. Ensure wiring is routed away from hot or moving engine components.
• Чишћење: Keep the exterior of the distributor clean and free from oil, grease, and dirt. Use a clean, dry cloth.
• Spark Plugs & Wires: For optimal performance, ensure your spark plugs and spark plug wires are in good condition and are compatible with electronic ignition systems.

КСНУМКС. Решавање проблема

If you experience issues with your ignition system, consider the following common problems and solutions:

If problems persist after troubleshooting, contact PerTronix technical support.

8. Спецификације

9. Гаранција и подршка

PerTronix products are manufactured to high standards and are backed by a limited warranty. For specific warranty terms and conditions, please refer to the warranty card included with your product or visit the official PerTronix webсајту.

For technical support, installation assistance, or warranty claims, please contact PerTronix customer service:

• Webсајт: ввв.пертроник.цом
• Телефон: Погледајте на webсајт за тренутне контакт бројеве.
• When contacting support, please have your product model number (D134600) and purchase information ready.