KeylessOption Даљински управљач за улазак у аутомобил без кључа и замена за кључ за LHJ011 Упутство за употребу

Увод

This manual provides detailed instructions for the KeylessOption Keyless Entry Remote Car Key Fob and Key Replacement, model LHJ011. It covers product overview, setup, programming, maintenance, and specifications to ensure proper use and functionality.

Производ је завршенview

The KeylessOption LHJ011 is a replacement keyless entry remote and key designed to function identically to your vehicle's original equipment. It includes a fully tested remote with a pre-installed battery and an uncut key blade.

Слика: Фронт view of two KeylessOption LHJ011 key fobs, each featuring lock and unlock buttons, a red panic button, and an attached uncut key blade. These units are designed for keyless entry and vehicle ignition.

Слика: Леђа view of two KeylessOption LHJ011 key fobs, showing the smooth, black plastic casing and the key ring attachment point. This view highlights the compact design of the remote units.

Setup and Key Cutting

Before programming the remote functions, the included key blade must be cut to match your vehicle's original key. This process is typically performed by a professional locksmith or an automotive dealership.

1. Key Cutting: Take the new key fob and your original vehicle key to a qualified locksmith or dealership. They will cut the new key blade to match your existing key. This is essential for starting the vehicle.
2. Инсталација батерије: The remote comes with a CR2032 battery pre-installed. If replacement is needed, refer to the maintenance section.

Operating Instructions: Remote Programming

The KeylessOption LHJ011 remote control functions (lock, unlock, panic) are self-programmable for many compatible vehicles. Follow these step-by-step instructions carefully. It is recommended to program all new and existing remotes in a single session.

General Programming Procedure (Example for GM Vehicles, verify specific vehicle instructions):

1. Припрема: Gather all key fobs (new and existing) you wish to program. Ensure all vehicle doors are closed.
2. Уђите у режим програмирања:
   • Седите на возачево место.
   • Држите притиснуто УНЛОЦК дугме на панелу возачових врата.
   • While holding the UNLOCK button, insert your newly cut key into the ignition.
   • Cycle the ignition to the ON position (do not start the engine), then immediately to ОФФ, а затим назад на ON, а затим да ОФФ опет.
   • Release the UNLOCK button on the door panel. The vehicle's door locks should cycle (lock and unlock) to confirm that the vehicle is now in programming mode.
3. Даљински управљач програма:
   • Take the first remote you wish to program (e.g., for Driver 1).
   • Истовремено притисните и држите ЛОЦК и УНЛОЦК дугмад на даљинском.
   • Continue holding these buttons until the vehicle's door locks cycle again (this may take 15 to 30 seconds, or up to 100 seconds). This confirms the remote has been programmed.
   • If you have additional remotes (e.g., for Driver 2), immediately repeat the previous step for each remaining remote. Do not exit programming mode between remotes.
4. Изађите из режима програмирања:
   • Once all remotes are programmed, turn the ignition key to the ON position, then to ОФФ.
   • Open the driver's door. This action typically exits the programming mode.
5. Test Remotes: Test all programmed remotes to ensure they function correctly (lock, unlock, panic). The first remote programmed will typically be assigned to Driver 1, and subsequent remotes to Driver 2, if your vehicle supports this feature.

Напомена: Specific programming procedures may vary slightly by vehicle make and model. Always refer to your vehicle's owner's manual or the manufacturer's recommended programming instructions if these steps do not work.

Одржавање

Замена батерије

The KeylessOption LHJ011 remote uses one CR2032 coin cell battery. When the remote's range decreases or it stops responding, the battery may need replacement.

1. Open the Fob Casing: Carefully pry open the remote's casing. There is usually a small notch on the side where you can insert a flat-head screwdriver or a coin to gently separate the two halves.
2. Уклоните стару батерију: Note the orientation (+/-) of the existing CR2032 battery. Gently remove it.
3. Уметните нову батерију: Insert a new CR2032 battery with the positive (+) side facing the same direction as the old battery.
4. Затвори Цasing: Align the two halves of the fob casing and press them firmly together until they snap securely into place.
5. Тест функционалност: Test the remote's functions (lock, unlock) to ensure the new battery is working correctly.

Напомена: Старе батерије одлажите одговорно у складу са локалним прописима.

Решавање проблема

Спецификације

• Модел: ЛХЈ011
• Бренд: КеилессОптион
• Број дела произвођача: КПТ4037
• ОЕМ бројеви делова: 15132198, 15186200, 15186201, 15186203, 15186209, 21997127, 22730827, LHJ011, 10377295, 15132197
• Тип батерије: 1 к ЦР2032 (укључено)
• Материјал: Пластика
• Димензије производа: Приближно 4 цм Д x 2 цм Ш
• Тежина артикла: Отприлике 1.58 унци
• Тип аутомобилске компатибилности: Специфично уклапање у возило
• Број дугмади: 2 (Lock, Unlock) + Panic

Гаранција и подршка

Each KeylessOption product includes a warranty card. For specific warranty details, please refer to the included card or contact KeylessOption customer support. Technical support is available with each purchase to assist with programming or operational questions.

For further assistance, please visit the official KeylessOption store or contact their customer service department.

KeylessOption Store: Посетите продавницу