Lindby Tommi Modern Plaster Wall Lamp Упутство за употребу

Увод

Thank you for choosing the Lindby Tommi Modern Plaster Wall Lamp. This manual provides essential information for the safe installation, operation, and maintenance of your new lighting fixture. Please read these instructions carefully before installation and retain them for future reference.

Важна безбедносна упутства

• електрична безбедност: Installation must be performed by a qualified electrician in accordance with all local and national electrical codes. Always disconnect power at the main circuit breaker before installation or maintenance.
• Волtage: Уверите се да је залиха волtagе одговара лampзахтеви (230 волти).
• Тип сијалице: Користите само сијалице са грлом Е14 са максималном снагомtage of 25 watts. LED bulbs are recommended.
• Материјал: Тхе лamp is made of plaster. Handle with care to prevent damage.
• Само за унутрашњу употребу: This product is designed for indoor use in dry locations. It is not water-resistant.
• топлота: Allow bulbs to cool before touching or replacing.

Садржај пакета

Пре почетка инсталације проверите да ли су све компоненте присутне:

• Lindby Tommi Wall Lamp причвршћивач (1 јединица)
• Монтажни материјал (шрафови, зидни типлови)
• Note: Light bulbs are not included.

Спецификације

Слика: Дијаграм димензија производа.

Подешавање и инсталација

Пре него што почнете: Ensure the power supply to the installation area is turned off at the circuit breaker. It is recommended to have a qualified electrician perform the installation.

1. Припремите место за монтажу: Изаберите одговарајућу локацију на зиду за лamp. Ensure there is adequate space and access to electrical wiring.
2. Означите тачке бушења: Hold the mounting bracket (or the lamp itself if the bracket is integrated) against the wall at the desired installation height. Use a pencil to mark the drilling points for the screws.
3. Избушене рупе: Drill holes at the marked points. Insert appropriate wall anchors if necessary, depending on your wall material.
4. Причврстите носач за монтажу: Причврстите носач за монтажу на зид помоћу приложених шрафова. Уверите се да је чврсто причвршћен.
   

   Слика: Интерна view од лamp showing the mounting bracket and wiring terminals.
5. Електрични прикључак: Повежите електричне жице од зида до лamp's terminal block.
   • Connect the live wire (usually brown or black) to the 'L' terminal.
   • Connect the neutral wire (usually blue) to the 'N' terminal.
   • Connect the earth wire (usually green/yellow) to the earth terminal (marked with ⚡).
   Уверите се да су све везе безбедне.
   

   Image: Close-up of the electrical terminal block for wiring connections.

6. Инсталирајте сијалице: Insert four E14 base light bulbs (not included) into the lamp holders. Do not exceed 25 watts per bulb.
   

   Image: Interior of the lamp with bulb sockets visible.
7. Монтирајте Лamp Распоред: Пажљиво поравнајте лamp fixture with the mounting bracket and secure it in place. Ensure it is stable and flush against the wall.
8. Врати снагу: Once the installation is complete and all connections are secure, restore power at the main circuit breaker.
9. Тестирајте Лamp: Укључите прекидач за светло да бисте осигурали да је лamp функционише исправно.

Видео водич за инсталацију

Упутство за употребу

The Lindby Tommi wall lamp is designed for simple operation via a standard wall switch. If connected to a compatible dimmer switch, the light output can be adjusted.

• Укључивање/искључивање: Use the wall switch connected to the lamp да бисте га укључили или искључили.
• Затамњење (опционо): If you have installed dimmable E14 bulbs and connected the lamp to a compatible dimmer switch, you can adjust the brightness by operating the dimmer switch.

Одржавање

• Чишћење: За чишћење лamp, ensure the power is off. Wipe the surface with a soft, dry cloth. Do not use abrasive cleaners or solvents, as these can damage the plaster finish.
• Замена сијалице:
  1. Искључите напајање лamp код прекидача.
  2. Оставите стару сијалицу да се потпуно охлади пре него што је додирнете.
  3. Carefully unscrew the old E14 bulb.
  4. Screw in a new E14 bulb, ensuring it does not exceed 25 watts.
  5. Restore power and test the lamp.

Решавање проблема

Гаранција и подршка

For warranty information, please refer to the terms and conditions provided at the point of purchase or contact your retailer. Lindby products are designed for quality and durability.

If you encounter any issues or require assistance, please contact Lindby customer support or your authorized dealer. Please have your model number (9613070) and purchase details ready.

For more information about Lindby products, visit the official Lindby brand store: Lindby Brand Store.