Увод
The Autotek MM2020.1D The Mean Machine Monoblock Class D Amplifier is designed to deliver high power output with minimal distortion for a mono subwoofer system. Featuring Pro-Fi high-speed MOSFETs and Class D technology, this amplifier provides efficient power in a compact design. It offers flexible connectivity options, including RCA outputs for daisy-chaining multiple ampлифиерс.
Безбедносне информације
УПОЗОРЕЊЕ: Овај производ садржи хемикалије за које је држава Калифорнија познато да узрокују рак и урођене недостатке или другу репродуктивну штету.
Производ је завршенview
Кључне карактеристике
- 2,000 watts mono bridged x 1 @ 4 ohms
- 500 watts x 1 @ 4 ohms
- 1,000 watts x 1 @ 2 ohms
- 0 to 12 dB bass boost
- Road Worthy TCID (Twin Coil Isolation Design) and Pro-Fi High Speed MOSFETS for extreme power with high sound quality and minimum distortion levels.
AmpРаспоред за снимање
Задњи панел view of the Autotek MM2020.1D amplifier, showing all input, output, power, and control connections.
Close-up of the power and speaker output terminals on the Autotek MM2020.1D amplifier, including the 60A fuse.
Close-up of the input level, subsonic filter, low pass filter, bass boost, and RCA input/output connections on the Autotek MM2020.1D ampлифиер.
Подешавање и инсталација
Прикључци за напајање
Connect the +12V terminal to the positive terminal of the car battery using appropriate gauge wire. Connect the -GND terminal to a solid chassis ground point. Ensure all connections are secure.
Прикључци звучника
Connect your subwoofer(s) to the SPEAKER OUTPUT terminals. Ensure correct polarity (+ to + and - to -). This amplifier is designed for mono subwoofer systems.
Улазно / излазне везе
Use RCA cables to connect the INPUT from your head unit or signal source. The OUTPUT RCA connections can be used to pass the audio signal to another ampлифиер.
Даљинско укључивање
Connect the REM terminal to the remote turn-on output of your head unit. This will turn the amplifier on and off with your car's audio system.
Инсталација осигурача
Тхе amplifier includes a 60A fuse. Ensure it is properly seated in its holder. Always replace with a fuse of the same rating.
Операција
Подешавање улазног нивоа
Adjust the INPUT LEVEL control (0.2V to 6V) to match the output voltage of your head unit. Start with the lowest setting and gradually increase until desired volume is achieved without distortion.
Субсониц Филтер
Use the SUBSONIC FILTER control (10Hz to 40Hz) to filter out extremely low frequencies that are inaudible and can waste amplifier power. Adjust based on your subwoofer's capabilities.
Нископропусни филтер
Adjust the LOW PASS filter (40Hz to 300Hz) to control the upper frequency limit of the amplifier's output, ensuring only bass frequencies are sent to the subwoofer.
Басс Боост
The BASS BOOST control (0dB to 12dB) allows for an increase in bass output at a specific frequency. Use sparingly to avoid distortion.
Индикаторска светла
- ПОВЕР (Green): Illuminates when the amplifier is receiving power and operating normally.
- ПРОТЕЦТ (Red): Illuminates when the amplifier enters protection mode due to a fault (e.g., short circuit, overheating, low voltagи).
Одржавање
To ensure optimal performance and longevity of your Autotek MM2020.1D amplifier, keep it free from dust and debris. Periodically check all wiring connections for tightness and corrosion. Avoid exposing the amplifier to excessive moisture or extreme temperatures.
Решавање проблема
| Проблем | Могући узрок | Решење |
|---|---|---|
| No Power (POWER LED off) | No +12V, GND, or REM connection | Check all power, ground, and remote wire connections. Verify fuse. |
| Amplifier in Protection Mode (PROTECT LED on) | Short circuit in speaker wiring, overheating, low voltage | Check speaker wiring for shorts. Ensure adequate ventilation. Verify vehicle's electrical system voltage. |
| Нема излаза звука | No input signal, incorrect gain setting, speaker wiring issue | Check RCA input cables. Adjust INPUT LEVEL. Verify speaker connections and polarity. |
| Дистортед Соунд | Input level too high, incorrect filter settings, damaged speakers | Reduce INPUT LEVEL. Adjust SUBSONIC FILTER and LOW PASS filter. Check speaker condition. |
Спецификације
| Феатуре | Спецификација |
|---|---|
| Модел | ММ2020.1Д |
| Output Power (Bridged Mono @ 4 Ohms) | 2,000 вати к 1 |
| Output Power (Mono @ 4 Ohms) | 500 вати к 1 |
| Output Power (Mono @ 2 Ohms) | 1,000 вати к 1 |
| Број канала | 1 (Моноблок) |
| Волtage | 6 волти (радно) |
| Димензије артикла (Д к Ш к В) | 11.81 к 9.84 к 2.28 инча |
| Тежина артикла | 454 грама |
| Врста материјала | Алуминијумска легура |
| Тип монтаже | Сурфаце Моунт |
| Гаранција | 1 година |
| Укључене компоненте | Производ, Упутство |
| УПЦ | 806576228042 |
Информације о гаранцији
The Autotek MM2020.1D amplifier comes with a 1-year limited warranty from the date of purchase. This warranty covers defects in materials and workmanship under normal use. Please retain your proof of purchase for warranty claims. For full warranty terms and conditions, refer to the documentation included with your product or visit the official Autotek webсајту.
Подршка
For technical assistance, troubleshooting, or warranty inquiries regarding your Autotek MM2020.1D amplifier, please visit the official Autotek website or contact their customer support department. Ensure you have your product model number (MM2020.1D) and proof of purchase available when seeking support.