Liftmaster 3 Ton Aluminum and Steel Low Profile High Lift Floor Jack

Важне информације о безбедности

Read and understand this entire manual before operating the Liftmaster 3 Ton Aluminum and Steel Low Profile High Lift Floor Jack. Failure to follow these instructions may result in serious injury or property damage. This floor jack is designed for lifting purposes only. Always use appropriate jack stands to support the vehicle after lifting. Never work under a vehicle supported only by a floor jack.

• Називни капацитет: Do not exceed the rated capacity of 3 tons (6000 lbs).
• Површина: Always use the jack on a hard, level surface. Avoid uneven ground or soft surfaces.
• Стабилност: Ensure the vehicle is stable and cannot roll before lifting. Engage the parking brake and block wheels.
• Џек Стендс: Immediately after lifting, place appropriately rated jack stands under the vehicle's designated support points.
• Преоптерећење: The dual pump quick lift hydraulic system is equipped with a safety valve to prevent overloading beyond rated capacity. Do not attempt to bypass this safety feature.
• Одржавање: Regularly inspect the jack for damage or wear. Do not use if damaged.

Сетуп

Before first use, perform the following steps to ensure proper operation and safety.

1. Распакивање: Carefully remove the floor jack from its packaging. Inspect for any shipping damage.
2. Склоп ручке: Insert the handle into the handle socket on the jack. Ensure it is securely seated.
3. Проверите причвршћиваче: Verify that all nuts and bolts, especially those on the casters, are securely tightened. Loose fasteners can affect stability and operation.
4. Bleeding the Hydraulic System: Air can become trapped in the hydraulic system during shipping. To bleed the system:
   • Окрените ручицу у смеру супротном од казаљке на сату да бисте потпуно отворили вентил за испуштање.
   • Pump the handle rapidly 10-15 times without a load.
   • Окрените ручицу у смеру казаљке на сату да бисте затворили вентил за отпуштање.
   • Тестирајте дизалицу тако што ћете је подићи до пуне висине, а затим је спустити. Поновите поступак ако је потребно док дизалица не почне да ради глатко.

Image: The Liftmaster 3 Ton Aluminum and Steel Low Profile High Lift Floor Jack in its lowered position, showcasing its gold and silver components.

Упутство за употребу

Follow these steps for safe and effective use of your floor jack.

1. Припремите возило: Park the vehicle on a hard, level surface. Engage the parking brake and place wheel chocks on the wheels that will remain on the ground.
2. Поставите Јацк: Locate the vehicle's manufacturer-recommended lifting points. Position the jack saddle directly under the lifting point. The jack's ultra-low 2.95 inch (75mm) entry point is ideal for lower body frame cars, while its high lift range up to 19.68 inches (500mm) accommodates pickups and SUVs.
3. Подигните возило: Turn the handle clockwise until the release valve is fully closed. Pump the handle to raise the vehicle. Lift the vehicle only high enough to place jack stands.
4. Обезбедите помоћу постоља за Џек: Once the vehicle is at the desired height, immediately place appropriately rated jack stands under the vehicle's designated support points.
5. Lower the Jack: Slowly turn the handle counter-clockwise to open the release valve and lower the jack until the vehicle rests securely on the jack stands. Remove the floor jack.
6. Remove Jack Stands and Lower Vehicle: When work is complete, raise the vehicle slightly with the floor jack to remove the jack stands. Then, slowly turn the handle counter-clockwise to lower the vehicle completely to the ground. Remove the floor jack and wheel chocks.

Image: The floor jack in a partially raised position, demonstrating its lifting capability.

Слика: Крупни план view of the jack's low profile, with a tape measure indicating its minimum height.

Одржавање

Редовно одржавање осигурава дуготрајност и безбедан рад ваше подне дизалице.

• подмазивање: Periodically lubricate all moving parts, including the pivot points and casters, with light machine oil.
• Хидраулична течност: Check the hydraulic fluid level regularly. If low, add high-quality hydraulic jack oil. Do not use brake fluid or other non-approved fluids.
• Чишћење: Keep the jack clean and free of dirt, grease, and corrosive materials.
• Release Valve Threads: If the release valve becomes stiff or causes the jack to lower too quickly, apply a small amount of oil to the threads of the release valve mechanism. This can help ensure a smooth and controlled lowering action.
• Складиштење: Чувајте дизалицу на чистом и сувом месту са потпуно увученим клипом како бисте спречили корозију и продужили век трајања заптивача.

Image: The jack with its saddle removed, showing the top plate where the saddle rests.

Слика: Крупни план view of the dual pump hydraulic mechanism, highlighting its components.

Решавање проблема

Погледајте овај одељак за уобичајене проблеме и њихова решења.

Спецификације

Информације о гаранцији

For detailed warranty information regarding your Liftmaster 3 Ton Aluminum and Steel Low Profile High Lift Floor Jack, please refer to the manufacturer's official webсајт или директно контактирајте њихову корисничку подршку. Сачувајте рачун као доказ о куповини.

Информације о подршци

For technical assistance, parts inquiries, or any other support needs, please contact LiftMaster customer support. Contact details can typically be found on the product packaging, the manufacturer's official webсајту или преко вашег продавца.