DROK Adjustable Current Voltage Analog Simulator Signal Generator

1. Увод

This manual provides comprehensive instructions for the DROK Adjustable Current Voltage Analog Simulator Signal Generator, Model 300482_JPN. This versatile module is designed to generate both 0/4-20mA current signals and 0-10V voltage signals, making it suitable for a wide range of industrial and testing applications. Please read this manual carefully before operation to ensure proper use and to prevent damage.

Слика 1: Одозго надоле view of the DROK Signal Generator, showing the digital display, control knob, and terminal block.

2. Спецификације

Image 2: Dimensions of the DROK Signal Generator, illustrating its compact size.

3. Карактеристике производа

• Dual Signal Output: Generates both 0/4-20mA current signals and 0-10V voltage signals from a single module.
• Подесиви излаз: Output signals are precisely adjustable using a multi-cycle potentiometer.
• Јасан ЛЕД екран: Features a bright, clear 3-digit LED digital display for real-time monitoring of output current and voltage.
• Easy Display Switching: A dedicated switch allows for quick toggling between current and voltage display modes.
• Калибрација екрана: Includes calibration potentiometers on the module's rear for fine-tuning the current and voltage display accuracy.
• Широка примена: Suitable for signal generation, valve adjustment, inverter control, PLC debugging, panel debugging, LED testing, and transmitter output simulation.

4. Подешавање

Before operating the signal generator, ensure proper power supply connection and output wiring.

1. Прикључак за напајање: Connect a DC 12-24V power source to the designated power input terminals (typically labeled '24V' and 'GND' or similar) on the terminal block. Ensure correct polarity.
2. Излазно ожичење: Connect your target device or multimeter to the appropriate output terminals. For current output, use the '0-20mA' terminals. For voltage output, use the '0-10V' terminals. Refer to the terminal block labels for precise connections.

Слика 3: Позади view of the DROK Signal Generator, showing the power supply and output voltage/current labels.

5. Операција

The signal generator features a main control knob and a display switch for easy operation.

1. Укључено: Once connected to a DC 12-24V power supply, the LED display will illuminate.
2. Select Output Type: Use the slide switch (labeled SW1 or similar) to select between voltage output (0-10V) or current output (0/4-20mA). The switch position will typically be indicated by labels such as '10V' for voltage and '20mA' for current.
3. Adjust Output Value: Rotate the multi-cycle potentiometer knob (labeled 'Min' to 'Max') to adjust the desired output signal. Turning the knob clockwise increases the output, and counter-clockwise decreases it.
4. Пребаците режим приказа: Press the button located below the LED display to toggle between displaying the output current and output voltage.

Image 4: Labeled diagram of the control panel. It shows the 3-digit digital display, the current/voltage display switch (left for voltage, right for current), and the multi-cycle adjustable potentiometer.

6. Display Calibration

The module includes calibration potentiometers on the back to ensure the displayed values match the actual output. A multimeter is required for accurate calibration.

Слика 5: Доња страна view of the DROK Signal Generator PCB, highlighting the two blue calibration potentiometers for current and voltage display adjustment.

6.1. Current Display Calibration

1. Rotate the main multi-cycle potentiometer knob clockwise to its maximum output.
2. Set the output type switch (SW1) to the current output position (e.g., '20mA').
3. Use an external multimeter to measure the actual output current value from the '0-20mA' terminals.
4. Adjust the current display adjustment potentiometer (located on the back of the module, refer to Image 5) until the value shown on the module's LED display matches the actual current value measured by the multimeter.

6.2. Волtage Display Calibration

1. Rotate the main multi-cycle potentiometer knob clockwise to its maximum output.
2. Set the output type switch (SW1) to the voltage output position (e.g., '10V').
3. Use an external multimeter to measure the actual output voltage value from the '0-10V' terminals.
4. Подесите јачину звукаtage display adjustment potentiometer (located on the back of the module, refer to Image 5) until the value shown on the module's LED display matches the actual voltage value measured by the multimeter.

7. Пријаве

The DROK Signal Generator is suitable for various applications, including but not limited to:

• General signal generation for testing and development.
• Valve adjustment and control.
• Inverter control systems.
• PLC (Programmable Logic Controller) debugging.
• Panel debugging and testing.
• LED testing and characterization.
• Transmitter output simulation.

КСНУМКС. Решавање проблема

9. Садржај пакета

The package for Model 300482_JPN typically includes:

• 1 x DROK Adjustable Current Voltage Analog Simulator Signal Generator

10. Гаранција и подршка

For warranty information or technical support, please refer to the product's purchase platform or contact DROK customer service directly. Keep your purchase receipt for warranty claims.