1. Увод
Хвала вам на куповиниasing the Lanzar HTG668BT 6-Channel Mosfet Ampлифиер. Ово amplifier is designed to provide high-quality audio performance for your vehicle's sound system, featuring a wireless Bluetooth audio interface for convenient streaming. Please read this manual thoroughly before installation and operation to ensure proper use and to maximize the performance and longevity of your ampлифиер.
Слика 1.1: Предња страна view of the Lanzar HTG668BT amplifier with key features highlighted.
2. Безбедносна упутства
Увек се придржавајте следећих мера безбедности током инсталације и рада:
- Препоручена професионална инсталација: Installation of car audio components requires experience with electrical wiring and automotive procedures. If you are unsure, consult a qualified professional.
- Искључите батерију: Before starting any wiring, disconnect the vehicle's negative battery terminal to prevent electrical shorts and damage.
- Правилно ожичење: Ensure all wiring is correctly connected, insulated, and secured to prevent shorts, overheating, and potential fire hazards. Use appropriate gauge wires for power and ground connections.
- вентилација: Инсталирајте amplifier in a location that allows for adequate air circulation to prevent overheating. Avoid mounting in enclosed spaces without ventilation.
- Заштита осигурача: Увек користите осигурач исправне јачине, као што је наведено. Никада не замењујте осигурач веће јачине. ampераге.
- Избегавајте влагу: Немојте излагати ampотпоран на влагу или воду.
- Контрола јачине звука: Дуготрајно излагање високој јачини звука може изазвати оштећење слуха. Подесите јачину звука на безбедан ниво.
3. Карактеристике производа
The Lanzar HTG668BT amplifier incorporates advanced technology for superior audio performance and user convenience:
- 6-канални Мосфет Ampдизалица: Пружа моћан и ефикасан аудио излаз.
- Wireless Bluetooth Audio Interface: Allows for wireless audio streaming from compatible devices.
- Излазна снага: 6 x 250W RMS @ 4 ohms, 6 x 350W RMS @ 2 ohms, 3 x 1000W Max @ 4 ohms bridged, 6 x 500W Max @ 4 ohms.
- Bass Boost Circuit: Побољшава одзив на ниским фреквенцијама.
- Bridgeable at 4 Ohms: Provides flexibility for various speaker configurations.
- 2 Ohm Stereo Stable: Ensures stable operation with low impedance loads.
- Chrome RCA Inputs: High-quality input connections.
- Стерео линијски излази: For connecting additional ampлифиерс.
- Low Pass Filter (LPF) Controls: Подесиво од 40Hz до 250Hz.
- High Pass Filter (HPF) Controls: Подесиво од 40Hz до 250Hz.
- Band Pass Filter (BPF) Controls: Adjustable from 40Hz-3KHz.
- Power and Protection LED Indicators: Visual status feedback.
- Soft Turn-On/Turn-Off: Prevents pops and thumps during power transitions.
- Заштитно коло: Includes thermal, overload, and speaker-short protection.
4. Садржај пакета
Проверите да ли су све ставке присутне у пакету:
- Lanzar HTG668BT 6-Channel Mosfet Ampлифиер
- Водич за брзи почетак
5. Подешавање и инсталација
Proper installation is crucial for optimal performance. Ensure the vehicle's battery is disconnected before proceeding.
5.1 Монтирање Ampлифиер
Изаберите место за монтажу које обезбеђује одговарајућу вентилацију и заштићено је од влаге. Причврстите amplifier firmly to a solid surface using appropriate hardware.
Слика 5.1: Примерampле од amplifier installation in a vehicle trunk.
5.2 Ожичење
Refer to the diagrams below for proper wiring of power, ground, remote, RCA inputs, and speaker outputs.
Image 5.2: Rear panel connections for power, ground, remote, and speaker outputs.
- Снага (BATT+): Connect to the positive terminal of the car battery using a heavy-gauge power cable (e.g., 4-gauge or larger, depending on total power draw) with an inline fuse located within 18 inches of the battery.
- Уземљење (ГНД): Connect to a clean, unpainted metal surface of the vehicle chassis. Ensure a solid, low-resistance connection. Use a cable of the same gauge as the power cable.
- Даљински управљач (REM): Connect to the remote turn-on output of your head unit. This wire turns the amplifier on and off with your car's audio system.
- РЦА улази: Повежите RCA каблове са предње стране ваше главне јединице.amp излази на amplifier's RCA input jacks. The HTG668BT features chrome RCA inputs.
- Излази за звучнике: Повежите звучнике на amplifier's speaker terminals. Observe correct polarity (+/-) for each speaker. The amplifier supports 2 Ohm stereo stable operation and can be bridged at 4 ohms.
Image 5.3: Front panel controls for RCA inputs, gain, and filter adjustments.
6. Упутство за употребу
6.1 Укључивање/искључивање
Тхе amplifier will power on automatically when the remote turn-on lead receives a signal from your head unit. The 'PWR' LED indicator will illuminate. The amplifier features a soft turn-on/turn-off circuit to prevent audible pops.
6.2 Стримовање звука преко Bluetooth-а
To stream audio wirelessly:
- Осигурајте ampЛифиер је укључен.
- Activate Bluetooth on your mobile device (smartphone, tablet, etc.).
- Тражи available Bluetooth devices and select 'Lanzar HTG668BT' (or similar name) to pair.
- Once paired, you can stream audio directly to the ampлифиер.
6.3 Adjusting Audio Settings
Користите контроле на amplifier's front panel (refer to Image 5.3) to fine-tune your audio:
- Контроле појачања: Adjust the input sensitivity to match the output level of your head unit. Start with the gain at minimum and slowly increase until desired volume is achieved without distortion.
- Нископропусни филтер (ЛПФ): Use this filter to allow only frequencies below the set point to pass through, typically used for subwoofers. Adjustable from 40Hz-250Hz.
- Високопропусни филтер (ХПФ): Use this filter to allow only frequencies above the set point to pass through, typically used for full-range speakers. Adjustable from 40Hz-250Hz.
- Band Pass Filter (BPF): Allows a specific range of frequencies to pass through. Adjustable from 40Hz-3KHz.
- Басс Боост: Adjust to enhance low-frequency output. Use sparingly to avoid distortion.
6.4 Bridging Channels
The HTG668BT amplifier can be bridged at 4 ohms to combine two channels into one, providing higher power output for a single speaker, such as a subwoofer. Refer to the wiring diagram on the amplifier or in the quick start guide for specific bridging instructions. Ensure the speaker connected to a bridged channel has a minimum impedance of 4 ohms.
7. Одржавање
Regular maintenance helps ensure the longevity and performance of your ampдизалица:
- Чишћење: Периодично обришите ampОбришите спољашњост уређаја меком, сувом крпом. Не користите јаке хемикалије или абразивна средства за чишћење.
- Проверите везе: Annually inspect all power, ground, remote, and speaker connections to ensure they are secure and free from corrosion. Loose connections can cause performance issues or damage.
- вентилација: Осигурајте amplifier's cooling fins are free from dust and debris to maintain proper heat dissipation.
КСНУМКС. Решавање проблема
Ако имате проблема са својим amplifier, consult the following troubleshooting guide:
| Проблем | Могући узрок | Решење |
|---|---|---|
| Нема напајања (PWR LED је искључен) | Blown fuse, loose power/ground/remote wire, no remote signal. | Проверите уграђени осигурач и amplifier fuses. Verify all power, ground, and remote connections are secure. Test remote wire for 12V signal. |
| Amplifier in Protection Mode (PRT LED on) | Прегревање, кратки спој звучника, оптерећење ниском импедансом, једносмерни помак. | Дозволи amplifier to cool. Check speaker wiring for shorts. Verify speaker impedance is within specifications (2 Ohm stereo stable, 4 Ohm bridged). Disconnect speakers and RCA inputs to isolate the issue. |
| Нема излаза звука | No input signal, incorrect gain setting, speaker wires disconnected, amplifier in protection. | Check RCA input connections. Adjust gain. Verify speaker connections. Refer to 'Amplifier in Protection Mode' solution. |
| Дистортед Соунд | Gain set too high, improper filter settings, poor ground connection, damaged speakers. | Reduce gain. Adjust LPF/HPF/BPF settings. Ensure ground connection is solid. Test speakers with another ampспасилац ако је могуће. |
| Проблеми са Блуетоотх везом | Device not in pairing mode, interference, amplifier not discoverable. | Осигурати amplifier is on and Bluetooth is enabled on your device. Try restarting both devices. Move closer to the ampлифиер. |
9. Спецификације
Technical specifications for the Lanzar HTG668BT 6-Channel Mosfet Ampдизалица:
- Канали: 6
- RMS снага на 4 ома: 6 к 250В
- RMS снага на 2 ома: 6 к 350В
- Max Power @ 4 Ohms Bridged: 3 к 1000В
- Max Power @ 4 Ohms: 6 к 500В
- Минимална импеданса: 2 Охм Стерео Стабилан
- Low Pass Filter (LPF) Frequency Response: 40Хз-250Хз
- High Pass Filter (HPF) Frequency Response: 40Хз-250Хз
- Band Pass Filter (BPF) Frequency Response: 40Хз-3КХз
- Тотална хармонијска дисторзија (ТХД): <0.04%
- Однос сигнал-шум (S/N): >90дБ
- Раздвајање канала: >65дБ
- Фреквенцијски одзив: 10Хз-45КХз
- Осигурачи: 3 к 25А
- Димензије (Д к В к Ш): 19.29'' x 2.24'' x 8.81'' (49 цм x 5.7 цм x 22.4 цм)
- Тежина артикла: 10.28 фунте (4.66 кг)
- Волtage: 0.2 Volts (Input Sensitivity)
- Тип монтаже: Сурфаце Моунт
10. Гаранција и подршка
Lanzar products are designed and manufactured to the highest quality standards. For specific warranty information, please refer to the warranty card included with your product or visit the official Lanzar website. If you require technical assistance or have questions regarding your amplifier, please contact Lanzar customer support through their official channels.