SINOTIMER MC101-611 Universal Intelligent Temperature Control Meter

1. Увод

The SINOTIMER MC101-611 is a universal intelligent temperature control meter designed for precise temperature and humidity management. It features a clear LCD display for process value (PV) and set value (SV), along with various output and alarm functions. This manual provides essential information for the safe and effective operation of your device.

Слика 1.1: Предња страна view of the MC101-611 Temperature Control Meter, showing the dual digital display and control buttons.

2. Безбедносне информације

• Пажљиво прочитајте сва упутства пре инсталације и рада.
• Уверите се да је напајање волtage matches the device's requirements (85-265V AC, 50/60Hz).
• All wiring should be performed by a qualified electrician to prevent electric shock or damage to the device.
• Do not operate the device in environments with excessive moisture, dust, or corrosive gases.
• Искључите напајање пре него што извршите било какво одржавање или промене ожичења.
• Држите уређај даље од јаких електромагнетних сметњи.

3. Карактеристике производа

• Universal input for various temperature sensors (K, J, E, T, R, S, B, Pt100, Cu50).
• Dual digital display for Process Value (PV) and Set Value (SV).
• Multiple control outputs: Relay and SSR (Solid State Relay).
• Alarm functions (AL1, AL2) for high/low limits.
• PID auto-tuning function for precise control.
• Wide operating temperature range.
• Compact and easy-to-install design.

4. Садржај пакета

• 1 x SINOTIMER MC101-611 Temperature Control Meter
• 1 x Mounting Bracket (as shown in Figure 4.1)
• 1 x Упутство за употребу (овај документ)

Figure 4.1: The MC101-611 unit alongside its included mounting bracket, essential for panel installation.

5. Подешавање

5.1 Монтажа

The MC101-611 is designed for panel mounting. Cut an appropriate opening in your control panel and insert the meter. Secure it from the rear using the provided mounting bracket. Ensure a snug fit to prevent vibration.

5.2 Ожичење

Refer to the wiring diagram on the side of the unit and Figure 5.1 for correct connections. Ensure all connections are secure and insulated. Incorrect wiring can damage the device or pose a safety hazard.

• Терминали 1 и 2: AC Power Supply (85-265V AC, 50/60Hz)
• Терминали 3 и 4: Main Output (OUT) - Normally Open (NO) and Normally Closed (NC) contacts for Relay output.
• Терминали 6 и 7: Alarm Output (ALM) - Relay contacts for alarm.
• Terminals 8, 9, 10: Sensor Input (RTD/TC) - Connect your temperature sensor here. Refer to the sensor's manual for correct polarity/connection type.
• Терминали 11 и 12: SSR Output - For connecting to a Solid State Relay.

Figure 5.1: Detailed wiring diagram on the side of the MC101-611, indicating connections for power, output, alarm, and sensor input.

6. Упутство за употребу

6.1 Приказ прекоview

The meter features a dual display:

• PV (Process Value): The upper red display shows the current measured temperature/humidity.
• SV (Подешена вредност): The lower green display shows the desired set point.
• ОУТ индикатор: Illuminates when the main output is active.
• АТ индикатор: Illuminates when the auto-tuning function is active.
• AL1/AL2 Indicators: Illuminate when Alarm 1 or Alarm 2 conditions are met.

6.2 Функције дугмета

• СЕТ дугме: Користи се за улазак у режим подешавања параметара и потврђивање избора.
• < / R/S Button: Used to shift digits during setting or to reset alarms.
• ▼ (Down) Button: Decreases the value of a parameter or set point.
• ▲ (Up) Button: Increases the value of a parameter or set point.

6.3 Setting the Temperature/Humidity Set Point (SV)

1. In normal operating mode, press the СЕТ button once. The SV display will begin to flash.
2. Користите ▲ (Горе и ▼ (Down) buttons to adjust the SV to your desired value. Use the < / R/S button to shift the cursor for faster adjustment.
3. Притисните тастер СЕТ button again to confirm the new SV and exit the setting mode.

6.4 Advanced Parameter Settings

To access advanced parameters (e.g., input type, control mode, alarm settings, PID parameters), press and hold the СЕТ button for approximately 3-5 seconds until the first parameter code appears on the PV display. Use the ▲ (Горе и ▼ (Down) buttons to navigate through parameters and the СЕТ button to enter and confirm values. Refer to the detailed parameter list in the full technical manual for specific codes and their functions.

7. Одржавање

• Чишћење: Обришите екран и цasinОбришите меком, сувом крпом. Не користите абразивна средства за чишћење или раствараче.
• инспекција: Периодично проверавајте спојеве ожичења да ли има лабавости или корозије.
• Складиштење: If storing the device for an extended period, ensure it is kept in a dry, dust-free environment within its specified storage temperature range.

КСНУМКС. Решавање проблема

9. Спецификације

Figure 9.1: Product label on the side of the MC101-611, detailing model, range, output, and power supply specifications.

10. Гаранција и подршка

This product comes with a standard manufacturer's warranty. Please refer to your purchase documentation for specific warranty terms and conditions. For technical support, troubleshooting assistance, or warranty claims, please contact the SINOTIMER customer service through the retailer where the product was purchased or visit the official SINOTIMER webсајт за контакт информације.