Увод
This manual provides detailed instructions for the installation, setup, operation, and maintenance of your Intermatic ET2705C Electronic Timer. This device is designed for precise control of electrical loads with its 7/365-day operation mode and single channel output. Please read this manual thoroughly before installation and use to ensure safe and efficient operation.
Важна безбедносна упутства
УПОЗОРЕЊЕ: Опасност од пожара или електричног удара
- Disconnect power at the circuit breaker(s) or disconnect switch(es) before installing or servicing this unit.
- More than one circuit breaker or disconnect switch may be required to de-energize the equipment before servicing. Ensure all power sources are off.
- Инсталација и/или ожичење морају бити у складу са националним и локалним захтевима за електричну енергију.
- Користите COPPER conductors ONLY.
- Do NOT remove the internal insulator.
For wiring, lift and remove the screw, then swing the plastic insulator covering the terminal aside. Replace the screw and plastic insulator covering the terminal before powering on.
Figure 1: Front panel of the Intermatic ET2705C Electronic Timer. This image displays the digital display, control buttons (MODE, DAY, ENTER/NEXT, ON/OFF, CLEAR MEM, CLEAR ENTRY, +, -), and important safety warnings in English, French, and Spanish regarding electrical shock and fire hazards, as well as wiring instructions.
Подешавање и инсталација
1. Монтажа
- The Intermatic ET2705C timer is designed for surface mounting.
- Ensure the mounting location is suitable for a metal enclosure and provides adequate ventilation.
- Securely fasten the timer to a flat, stable surface using appropriate hardware.
2. Ожичење
- Before beginning any wiring, ensure all power to the circuit is disconnected at the main breaker or disconnect switch. Verify with a voltagе тестер.
- Open the timer enclosure. Locate the terminal block.
- To access the wiring terminals, lift and remove the screw, then swing the plastic insulator covering the terminal block aside as indicated on the unit.
- Connect the appropriate copper conductors to the terminals as per the wiring diagram provided inside the unit and local electrical codes. This unit supports 120 to 277Vac voltage.
- Once wiring is complete, replace the plastic insulator covering the terminal block and secure it with the screw.
- Close the timer enclosure.
3. Почетно укључивање
- Restore power to the circuit. The timer display should illuminate.
- Allow the internal capacitor to charge for a few minutes. The timer has a 100-hour backup time in case of power loss.
Упутство за употребу
Control Buttons Overview:
- НАЧИН: Cycles through different programming modes (e.g., time setting, program setting).
- ДАН: Selects the day of the week during time setting or program scheduling.
- ENTER/NEXT: Потврђује изборе и прелази на следеће подешавање.
- УКЉУЧЕНО/ИСКЉУЧЕНО: Manual override for immediate ON/OFF control.
- CLEAR MEM: Clears all programmed settings.
- CLEAR ENTRY: Clears the current entry during programming.
- +: Increases values (e.g., hour, minute, program number).
- -: Decreases values (e.g., hour, minute, program number).
1. Setting Current Time and Date
- Притисните тастер МОДЕ button until the time setting mode is displayed.
- Користите + or - дугмад за подешавање сата, а затим притисните ЕНТЕР/НЕКСТ.
- Repeat for minutes and AM/PM (if applicable).
- Користите ДАН button to select the current day of the week, then press ЕНТЕР/НЕКСТ потврдити.
2. Programming Schedules (7/365 Day Operation)
The timer supports up to 96 ON/OFF cycles. Each program consists of an ON time and an OFF time.
- Притисните тастер МОДЕ button until "PROG" or "PROGRAM" is displayed.
- The display will show "1 ON". Use + or - to set the desired ON time (hour and minute), then press ЕНТЕР/НЕКСТ.
- Користите ДАН button to select the days of the week for this program (e.g., Mon-Fri, Sat-Sun, or individual days). Press ЕНТЕР/НЕКСТ.
- The display will then show "1 OFF". Set the desired OFF time using + or -, а затим притисните ЕНТЕР/НЕКСТ.
- Repeat steps 2-4 for additional programs.
- Да бисте изашли из режима програмирања, притисните МОДЕ док се не прикаже тренутно време.
3. Мануал Оверриде
Притисните тастер ОН/ОФФ button to manually switch the connected load ON or OFF, overriding the current program. The timer will resume programmed operation at the next scheduled event.
Одржавање
- Ensure power is disconnected before performing any maintenance.
- Periodically inspect the timer for any signs of damage or loose connections.
- Очистите спољашњост уређаја меком, сувом крпом. Не користите абразивна средства за чишћење или раствараче.
- The internal capacitor provides backup power for up to 100 hours during power outages. No user maintenance is required for the backup device.
Решавање проблема
| Проблем | Могући узрок | Решење |
|---|---|---|
| Екран је празан. | Нема напајања за јединицу. | Check circuit breaker or disconnect switch. Ensure wiring is correct. |
| Timer not switching load ON/OFF as programmed. | Incorrect program settings; Manual override active; Incorrect time/date. | Verify program settings, current time, and date. Check if manual override is engaged. |
| Дугмад не реагују. | Привремени софтверски квар. | Покушајте да притиснете CLEAR MEM (if safe to clear programs) or temporarily disconnect power for a few seconds and restore. |
Спецификације
| Број модела | ЕТ2705Ц |
| Оперативни режим | 7/365 дана |
| Број канала | 1 |
| Контакт образац | СПСТ |
| Волtage | 120 до 277Вац |
| Ampераге | 30 Amps |
| HP @ 120V | 1 ХП |
| HP @ 240V | 2 ХП |
| Max. ON/OFF Cycles | 96 |
| Number of Pulse Events | 0 |
| Енцлосуре | Метал |
| Монтажа | Површина |
| Број полова | 1 |
| Min. Time Setting | 1 минут |
| Макс. Подешавање времена | 7 дана |
| НЕМА Ратинг | 1 |
| Боја | Греи |
| Бацкуп Девице | кондензатор |
| Бацкуп Тиме | 100 сата |
| Радна температура | -40°Ф до 155°Ф (-40°Ц до 68°Ц) |
| Димензије производа (В к Ш к Д) | 7.88 cm x 5.13 cm x 3.44 cm |
| Тежина артикла | 8 унци |
| Материјал | Метал |
| Стандарди | UL Listed, California Title 20 Listed, LED Listed |
Информације о гаранцији
For detailed warranty information, please refer to the official Intermatic website or the warranty card included with your product. General warranty terms typically cover defects in materials and workmanship for a specified period from the date of purchase.
Корисничка подршка
If you require technical assistance or have questions regarding your Intermatic ET2705C Electronic Timer, please visit the official Intermatic website for support resources, FAQs, and contact information. You may also refer to the contact details provided on the product packaging.