Hantek DSO2D10 Digital Storage Oscilloscope User Manual

1. Увод

This manual provides essential information for the safe and effective operation of your Hantek DSO2D10 Digital Storage Oscilloscope. Please read this manual thoroughly before using the device to ensure proper functionality and to prevent damage.

Figure 1: Hantek DSO2D10 Digital Storage Oscilloscope

2. Безбедносне информације

Always observe the following safety precautions to prevent injury and avoid damage to the instrument or any products connected to it.

• Извор напајања: Use only the power cord specified for this instrument. Ensure the power supply voltagе је унутар наведеног опсега.
• уземљење: The instrument must be properly grounded. Do not defeat the grounding conductor of the power cord.
• Безбедност сонде: Ensure probes are correctly connected and rated for the voltage being measured. Do not touch exposed connections or components when power is applied.
• Окружење: Operate the instrument in a well-ventilated area. Do not operate in wet or damp conditions, or in explosive atmospheres.
• Одржавање: Сва сервисирања препустите квалификованом сервисном особљу. Не покушавајте сами да сервисирате инструмент.

3. Производ је готовview

3.1 Кључне карактеристике

• Features 2 independent channels with dedicated knob control.
• 100 MHz analog bandwidth and 1 GSa/s real-time sampлинг рате.
• Equipped with a 7-inch TFT LCD screen, 800x480 pixels, displaying 16 million colors (24-bit true color).
• Integrated 25 MHz signal generator, supporting arbitrary waveform burst output and modulation waveform output.
• Capable of saving parameters, waveforms, reference waveforms, CSV, and images.
• Includes 5-digit digital voltmeter and 6-digit hardware frequency counter functions.
• Large storage depth of 8Mpts to minimize waveform distortion and restore real waveforms.

3.2 Физички опис

The Hantek DSO2D10 is designed for portability and ease of use. Below are various viewс уређаја.

Figure 2: Front, Rear, and Side Views

The device measures approximately 318mm in width, 140mm in depth, and 150mm in height, making it compact for various applications.

Figure 3: Oscilloscope Dimensions

3.3 Идентификација компоненте

Familiarize yourself with the main components and controls of the oscilloscope.

Слика 4: Изглед предњег панела

• ЛЦД екран: 7-inch TFT screen for waveform display and menu navigation.
• Option Buttons (F1-F6): Контекстно осетљиви функционални тастери.
• Executive Control Buttons: Buttons for various functions like Menu, Utility, Cursor, Display, Acquire, etc.
• Вертикалне контроле: VOLTS/DIV knobs and POSITION knobs for Channel 1 (CH1) and Channel 2 (CH2).
• Хоризонталне контроле: SEC/DIV knob and POSITION knob for time base adjustment.
• Ниво окидача: Knob to adjust the trigger level.
• Analog Channel Input (CH1, CH2): BNC connectors for probe input.
• External Trigger Input (EXT TRIG/GEN OUT): BNC connector for external trigger or signal generator output.
• УСБ интерфејс: For data transfer and firmware updates.
• Прекидач: Да бисте укључили или искључили уређај.

4. Подешавање

4.1 Распакивање и преглед

Carefully remove the oscilloscope from its packaging. Inspect the device for any signs of damage during transit. Retain the packaging for future storage or shipping.

4.2 Прикључак за напајање

1. Уверите се да је прекидач за напајање у положају ОФФ.
2. Connect the provided power cable to the power input on the rear panel of the oscilloscope.
3. Укључите други крај кабла за напајање у уземљену утичницу са наизменичном струјом.

4.3 Компензација сонде

Before taking measurements, it is crucial to compensate your oscilloscope probes to ensure accurate readings. This process adjusts the probe's capacitance to match the oscilloscope's input impedance.

1. Connect a probe to Channel 1 (CH1) input.
2. Connect the probe tip to the probe compensation output (usually a square wave test point on the front panel) and the ground clip to the ground terminal.
3. Turn on the oscilloscope. A square wave should appear on the screen.
4. Using a small screwdriver, adjust the compensation screw on the probe body until the square wave displayed on the screen has flat tops and bottoms with no overshoot or undershoot.
5. Repeat for other probes and channels as necessary.

5. Упутство за употребу

5.1 Укључивање/искључивање

Press the Power Switch located on the front panel to turn the oscilloscope ON or OFF.

5.2 Основни приказ таласног облика

1. Connect a signal source to CH1 using a compensated probe.
2. Подесите ВОЛТИ/ДЕЛ knob for CH1 to set the vertical scale.
3. Подесите СЕЦ/ДИВ knob to set the horizontal (time) scale.
4. Подесите ПОСИТИОН knobs (vertical and horizontal) to center the waveform on the screen.
5. Подесите TRIGGER LEVEL knob until a stable waveform is displayed.

5.3 Аутоматска мерења

The DSO2D10 supports 32 types of automatic measurements, simplifying waveform analysis.

Figure 5: Automatic Measurement Display

To access automatic measurements, press the МЕАСУРЕ button and use the option buttons (F1-F6) to select desired parameters such as Frequency, Period, Peak-to-Peak Voltage, RMS Voltage, etc. The results will be displayed on the screen.

5.4 Функција генератора сигнала

The built-in 25 MHz signal generator can output various waveforms. Connect the EXT TRIG/GEN OUT BNC connector to your circuit under test.

1. Притисните тастер ПОПУЊЕНО button or navigate through the menu to access the signal generator settings.
2. Select the desired waveform type (e.g., sine, square, arbitrary).
3. Adjust parameters such as frequency, amplitude, and duty cycle using the corresponding controls or menu options.

5.5 Чување и опозив података

The oscilloscope features an 8Mpts storage depth, allowing for detailed waveform capture and analysis. You can save and recall various data types.

Figure 6: Waveform Storage Depth

To save data, press the SAVE/TO USB button and follow the on-screen prompts to save parameters, waveforms, or screenshots to internal memory or a connected USB drive.

5.6 Digital Voltmeter and Frequency Counter

The DSO2D10 includes integrated 5-digit digital voltmeter (DVM) and 6-digit hardware frequency counter functions for precise measurements.

Figure 7: Dual DVM and Frequency Counter

These functions can be accessed via the КОМУНАЛНОСТ or МЕАСУРЕ menus, providing real-time digital readouts of voltagе и фреквенција.

6. Одржавање

6.1 Чишћење

Редовно чистите инструмент меком крпомamp cloth. Do not use abrasive cleaners or solvents that could damage the casing or screen. Ensure the device is powered off and unplugged before cleaning.

6.2 Калибрација

The oscilloscope is factory calibrated. For continued accuracy, periodic calibration by qualified service personnel is recommended, especially after significant temperature changes or prolonged use.

6.3 Складиштење

When not in use, store the oscilloscope in a dry, dust-free environment, away from direct sunlight and extreme temperatures. Use the original packaging for long-term storage if available.

КСНУМКС. Решавање проблема

This section addresses common issues you might encounter with the Hantek DSO2D10.

8. Спецификације

The following table details the technical specifications of the Hantek DSO2D10 Digital Storage Oscilloscope.

For a comparison with other models, refer to the table below:

Слика 8: Табела поређења модела

9. Гаранција и подршка

For warranty information and technical support, please refer to the official Hantek webсајт или контактирајте локалног дистрибутера. Сачувајте рачун као доказ о куповини.

Произвођач: Хантек