eSUN eBOX Lite Upgraded 3D Printing Filament Dryer Box User Manual

1. Производ је готовview

The eSUN eBOX Lite is an upgraded filament dryer box designed to maintain optimal conditions for 3D printing filaments. It effectively removes moisture, preventing common printing issues such as stringing, clogging, and poor adhesion. This device also functions as a filament storage box and spool holder, providing a comprehensive solution for filament management.

Key features include efficient heating, even temperature distribution, low-noise operation, and broad compatibility with various filament types and spool sizes.

Figure 1: eSUN eBOX Lite Filament Dryer Box with a red filament spool inside.

2. Садржај пакета

Проверите да ли су све ставке присутне у пакету:

• eBOX Lite Dryer Box
• Адаптер за напајање (амерички утикач)
• User Manual (this document, and a physical copy)
• Filament Outlet Tube/Bayonet

Figure 2: Illustration of the eBOX Lite and its included accessories.

3. Упутства за подешавање

1. Пласман: Place the eBOX Lite on a stable, flat surface away from direct sunlight, heat sources, and excessive humidity. Ensure adequate ventilation around the unit.
2. Прикључак за напајање: Connect the provided power adapter to the DC input port on the back of the eBOX Lite. Plug the adapter into a standard US power outlet (AC100-240V ~ 50/60Hz).
3. Учитавање филамента:
   • Open the transparent lid of the eBOX Lite.
   • Place your filament spool onto the internal rollers. Ensure the spool rotates freely. The maximum compatible spool size is Φ200mm (diameter) x 73mm (height).
   • Thread the filament through the designated outlet hole on the lid. If using the outlet conduit, attach it to the hole and thread the filament through it.
   • Добро затворите поклопац.

Figure 3: Visual guide for connecting power and loading filament.

4. Упутство за употребу

The eBOX Lite features a simple control panel with a display and buttons for setting temperature and time.

4.1. Цонтрол Панел Оверview

• Приказ: Shows current settings (temperature level, time remaining).
• Дугме за режим: Used to cycle between temperature setting mode and time setting mode.
• Дугмад за горе/доле: Used to adjust values (temperature level, time).

4.2. Подешавање температуре и времена

1. Укључено: After connecting the power, the display will light up.
2. Set Temperature Level:
   • Притисните тастер Режим button once to enter temperature setting mode. The display will show a number (1, 2, or 3).
   • Користите Горе/Доле buttons to select the desired temperature level based on your filament type:
   • Ниво 1: Approximately 40°C (suitable for PLA/PLA+)
   • Ниво 2: Approximately 50°C (suitable for ABS/ABS+/PETG)
   • Ниво 3: Approximately 55°C (suitable for PVA/Nylon/PC)
   • Притисните тастер Режим button again to confirm the temperature level and proceed to time setting.
3. Set Heating Time:
   • The display will now show the time setting (e.g., "00.0h").
   • Користите Горе/Доле buttons to set the desired heating duration from 0 to 18 hours. For optimal drying, eSUN recommends at least 2 hours for most filaments.
   • Притисните тастер Режим button again to start the drying process. The display will show the remaining time.

The eBOX Lite will maintain the set temperature and humidity throughout the drying cycle. Once the time expires, the heating will stop, but the box will continue to provide a dry storage environment.

Figure 4: Recommended temperature levels and corresponding filament types.

Figure 5: Graph illustrating humidity reduction over time during drying.

5. Одржавање

Regular maintenance ensures the longevity and optimal performance of your eBOX Lite.

• Чишћење: Wipe the exterior of the unit with a soft, dry cloth. Do not use abrasive cleaners or solvents. Ensure the unit is unplugged before cleaning.
• Унутрашње чишћење: Periodically check the inside of the box for any dust or filament debris. Use a soft brush or compressed air to remove any accumulation.
• Складиштење: Када се не користи дуже време, искључите уређај и чувајте га на хладном и сувом месту.

КСНУМКС. Решавање проблема

7. Спецификације

Figure 6: Detailed product specifications and package contents.

8. Гаранција и подршка

For warranty information and technical support, please refer to the official eSUN webсајт или директно контактирајте њихову корисничку службу. Сачувајте рачун као доказ о куповини.

You can also find additional resources and a PDF version of the user manual at: eSUN eBOX Lite User Manual (PDF)