U.S. Solid Motorized Ball Valve - 1" Stainless Steel

1. Увод

This manual provides detailed instructions for the safe and efficient installation, operation, and maintenance of your U.S. Solid Motorized Ball Valve. This 1-inch stainless steel valve features a full port design, 9-24V AC/DC compatibility, and a 2-wire auto-return setup, making it suitable for various home automation and industrial applications. Please read this manual thoroughly before installation and operation.

2. Безбедносне информације

WARNING: Failure to follow these safety instructions may result in property damage, serious injury, or death.

• Ensure the power supply is disconnected before any installation, maintenance, or troubleshooting.
• Проверите да ли је волtage and current ratings of your power source match the valve's requirements (9-24V AC/DC).
• Install the valve in an environment suitable for its IP65 rating, protecting it from dust and water jets.
• Do not exceed the maximum operating pressure of 10 Bars.
• Ensure proper threading (NPT) and secure connections to prevent leaks.
• This valve is designed for fluid control; do not use it for purposes other than its intended application.

3. Карактеристике производа

• Сигурно и поуздано: Constructed from 304 stainless steel, ensuring durability and an estimated life expectancy of 80,000 to 100,000 cycles.
• NPT Threading: Features 1-inch quality 304SS NPT threads, designed to minimize pressure loss with its full port bore.
• Виде Волtagе Распон: Operates effectively across a 9V-24V AC/DC range, opening or closing the valve in 3-5 seconds.
• 2-Wire Automatic Return Setup: Simple two-wire connection. The valve largely de-energizes after closing and returns to fully open if power is removed.
• Alternative to Solenoid Valves: Automatically cuts off power once fully open or fully closed, reducing the likelihood of overheating.

4. Спецификације

5. Подешавање и инсталација

5.1. Распакивање и преглед

Carefully remove the motorized ball valve from its packaging. Inspect the valve for any signs of damage during transit. Ensure all components are present and intact before proceeding with installation.

Слика 1: Предња страна view of the U.S. Solid Motorized Ball Valve.

5.2. Физичка инсталација

The valve features NPT threading for secure pipe connections. Apply appropriate thread sealant (e.g., Teflon tape) to the male pipe ends before screwing them into the valve. Ensure connections are firm and watertight to prevent leaks.

Figure 2: Proper application of Teflon tape for a watertight seal.

5.3. Electrical Wiring (2-Wire Auto Return)

The 2-wire auto return motorized ball valve is designed for simple electrical connection. It operates by energizing one wire to open the valve and de-energizing it to allow the valve to return to its default (open or closed) position. For this model, the valve is normally open and closes when power is applied.

Refer to the wiring diagram below for correct connections:

Figure 3: 2-Wire Auto Return Wiring Diagram for DC and AC power sources.

• Connect the red wire to the positive (+) terminal of your power source.
• Connect the green wire to the negative (-) terminal of your power source.
• When power is applied, the valve will close. When power is removed, the valve will automatically return to its fully open position.

6. Упутство за употребу

6.1. Основна операција

This motorized ball valve operates on a simple 2-wire auto-return principle. The valve's default state is normally open. When electrical power (9-24V AC/DC) is supplied to the red and green wires, the internal motor activates, rotating the ball to the closed position. Once the valve is fully closed, a limit switch minimizes power consumption. When the power supply is interrupted or removed, the valve automatically returns to its fully open position.

• To Close the Valve: Apply 9-24V AC/DC power to the red (positive) and green (negative) wires. The valve will rotate to the closed position in approximately 3-5 seconds.
• To Open the Valve: Remove the power supply from the red and green wires. The valve will automatically rotate back to the fully open position.

7. Одржавање

Regular maintenance ensures the longevity and optimal performance of your motorized ball valve.

• Периодични преглед: Regularly check the valve and connections for any signs of leaks, corrosion, or physical damage.
• Чишћење: Keep the exterior of the valve and actuator clean and free from debris. Use a soft, damp крпа за чишћење. Немојте користити абразивна средства за чишћење или раствараче.
• Електричне везе: Periodically inspect electrical wiring for secure connections and insulation integrity.
• Складиштење: If storing the valve for an extended period, ensure it is clean, dry, and stored in a temperate environment.

КСНУМКС. Решавање проблема

9. Гаранција и подршка

U.S. Solid stands by the quality of its products. This motorized ball valve comes with a 1-year warranty or money-back promise, ensuring customer satisfaction. For technical support, warranty claims, or any inquiries regarding your U.S. Solid product, please visit our official webсајту или контактирајте наш тим за корисничку подршку.

Webсајт: ввв.уссолид.цом

We are committed to delivering quality and affordability.