Увод
The Behringer CLOCKED SEQUENTIAL CONTROL MODULE 1027 is a faithful reproduction of the legendary 2500 Series 8-position step sequencer. Designed for Eurorack systems, this module provides precise control over voltage and gate signals, making it an essential tool for creating complex melodic and rhythmic patterns in your modular synthesizer setup. Its robust design and intuitive interface ensure reliable performance and creative flexibility.
Важна безбедносна упутства
- Read these instructions thoroughly before operating the module.
- Сачувајте ова упутства за будућу употребу.
- Heed all warnings on the product and in the manual.
- Пратите сва упутства за безбедан рад.
- Не користите овај апарат у близини воде или влаге.
- Чистите само сувом крпом.
- Не блокирајте вентилационе отворе. Инсталирајте у складу са упутствима произвођача.
- Не постављајте у близини извора топлоте као што су радијатори, грејни регистри, пећи или други уређаји (укључујући ampлифиерс) који производе топлоту.
- Користите само додатке/прибор које је навео произвођач.
- Упућивање свих сервиса квалификованом сервисном особљу. Сервисирање је потребно ако је апарат на било који начин оштећен.
Сетуп
Еурорацк Инсталлатион
The CLOCKED SEQUENTIAL CONTROL MODULE 1027 is designed for installation into a standard Eurorack case. Ensure your Eurorack case has sufficient power and space (16 HP width) before installation.
- Искључивање: Always disconnect power from your Eurorack case before installing or removing any modules.
- Монтажа: Align the module with an available 16 HP space in your Eurorack case. Secure it using the provided screws.
- Прикључак за напајање: Connect the 16-pin power cable from your Eurorack power supply to the module's power header. Ensure the red stripe on the cable aligns with the -12V pin on both the module and the power supply. Incorrect connection can damage the module and/or power supply.
- Укључено: Once securely mounted and connected, you can power on your Eurorack case.
Слика 1: Предња страна view of the Behringer 1027 module, showing all controls and patch points. This image illustrates the module's layout for proper installation and connection within a Eurorack system.
Почетне везе
To begin using the 1027, connect its outputs to other modules in your Eurorack system. Common connections include:
- Clock Input (CLK IN): Connect a clock signal from another module (e.g., an LFO or clock divider) to the CLK IN jack to drive the sequencer.
- CV Outputs (CH A, CH B, CH C): Patch these outputs to the CV inputs of oscillators, filters, or other modules to control pitch, cutoff, or other parameters.
- Gate Outputs (POSITION GATES 1-8): Connect these to gate inputs of envelope generators or drum modules to trigger events at specific steps.
Слика 2: Крупни план view of the input and output jacks on the Behringer 1027 module, highlighting the various patch points for integration into a modular system.
Упутство за употребу
Готовоview оф Цонтролс
The 1027 module features a clear layout of controls for intuitive sequencing:
- Дугме за брзину: Adjusts the speed of the internal clock. The range switch (LOW/HIGH) selects the clock speed range.
- PULSE WIDTH Knob: Controls the width of the gate pulses. The switch (INT/EXT) selects between internal control or external CV control.
- ОН/ОФФ прекидач: Toggles the sequencer's operation.
- STEP Buttons (1-8): Each step has a corresponding button to activate/deactivate it.
- CV Knobs (A, B, C for each step): Adjust the control voltage output for each of the three channels (A, B, C) at each step.
- POSITION GATES (1-8): Individual gate outputs for each step.
- STEP/RESET Buttons: Manual step advance and reset functions.
Слика 3: Под углом view of the Behringer 1027 module, providing a clear perspective of the control knobs and buttons for each step and channel.
Creating a Sequence
- Подесите сат: Користите РАТЕ дугме и ЛОВ/ХИГХ switch to set the desired tempo. Alternatively, connect an external clock to the ЦЛК ИН Јацк.
- Activate Steps: Притисните тастер СТЕП buttons (1-8) to activate the desired number of steps in your sequence. Active steps will typically illuminate.
- Adjust CV: For each active step, turn the CV Knobs (A, B, C) да се подеси волtage level for each channel. These voltages will be outputted sequentially.
- Configure Gates: Тхе ПОЛОЖАЈНЕ КАПИЈЕ will output a pulse when their corresponding step is active. Use these to trigger envelopes or other events.
- Старт/Стоп: Користите ОН/ОФФ switch to start and stop the sequence.
Напредне функције
- External Pulse Width Control: Connect a CV source to the EXT input for the PULSE WIDTH section to dynamically control the gate pulse width.
- Manual Step/Reset: Тхе СТЕП и РЕСЕТ buttons allow for manual control over the sequence progression, useful for live performance or precise programming.
Одржавање
Чишћење
To maintain the appearance and functionality of your module:
- Always power off your Eurorack system before cleaning.
- Use a soft, dry, lint-free cloth to wipe the module's surface.
- За тврдокорну прљавштину, благо дampИсперите крпу водом. Избегавајте употребу јаких хемикалија или абразивних средстава за чишћење.
- Do not allow any liquids to enter the module through jacks or openings.
Складиштење
When not in use for extended periods, store the module in a cool, dry place, away from direct sunlight and extreme temperatures. If removed from the Eurorack case, store it in anti-static packaging.
Решавање проблема
| Проблем | Могући узрок | Решење |
|---|---|---|
| Модул се не укључује. | Incorrect power cable connection; Eurorack power supply off or faulty. | Check power cable orientation (red stripe to -12V). Ensure Eurorack power supply is on and functioning correctly. |
| Sequencer not advancing steps. | No clock signal; ON/OFF switch is OFF; RATE knob set too low. | Connect a clock signal to CLK IN. Ensure ON/OFF switch is ON. Increase the RATE knob setting. |
| No CV output from a channel. | CV knob for that step/channel is at minimum; step is not active. | Adjust the corresponding CV knob. Ensure the step is active (illuminated). |
| No Gate output from a position. | Step is not active; PULSE WIDTH set to minimum. | Ensure the step is active. Increase the PULSE WIDTH setting. |
Спецификације
| Феатуре | Детаљ |
|---|---|
| Назив модела | 1027 |
| Модуле Типе | Секвенцијални контролни модул са тактом |
| Сериес | 2500 Сериес |
| Формат | Еурорацк |
| Ширина | 16 ХП |
| Дубина | Not specified (typical Eurorack depth) |
| Потрошња енергије | Not specified (standard Eurorack +12V, -12V) |
| Инпутс | Clock In, External Pulse Width CV |
| Излази | 3 x CV (A, B, C), 8 x Gate (Position Gates) |
| Димензије (В к Ш к Д) | 43 к 162 к 129 мм (приближно 1.69 к 6.38 к 5.08 инча) |
| Тежина артикла | 0.77 фунти (приближно 0.35 кг) |
| Технологија повезивања | 3.5mm TS jack |
| Извор напајања | DC power supply (via Eurorack bus) |
Гаранција
Behringer products are covered by a limited warranty. For detailed information regarding warranty terms, conditions, and registration, please visit the official Behringer website or the Music Tribe Community portal. Warranty services are typically handled through authorized service centers.
Опис гаранције: Community. Musictribe. Com.
Подршка
For further assistance, technical support, or to download the latest firmware and documentation, please visit the official Behringer webсајт:
- Behringer Official Webсајту
- Music Tribe Community (for warranty and support information)
You can also contact your local Behringer dealer or distributor for product-specific inquiries.