MACHINIST B75 Micro ATX LGA 1155 Motherboard Instruction Manual

1. Увод

This instruction manual provides essential information for the proper installation, configuration, and maintenance of your MACHINIST B75 Micro ATX LGA 1155 Motherboard. Please read this manual thoroughly before proceeding with installation to ensure correct setup and to prevent potential issues. This motherboard is designed to support Intel 2nd and 3rd generation Core i3/i5/i7, Xeon E3/V2 series, Celeron G series, and Pentium G series processors.

2. Спецификације

The following table outlines the key technical specifications of the MACHINIST B75 Micro ATX LGA 1155 Motherboard.

Напомена: Спецификације су подложне променама без претходне најаве.

Слика 2.1: Завршеноview of the B75 Pro U5 Motherboard layout.

3. Подешавање и инсталација

Пре почетка инсталације, уверите се да је систем искључен из напајања и да је кабл искључен из зидне утичнице. Држите матичну плочу за ивице како бисте избегли статичко пражњење.

3.1. Инсталација процесора

1. Пронађите ЛГА 1155 утичницу на матичној плочи.
2. Press the wire buckle by hand and lift it up. Do not remove the black protective cover before installing the CPU.
3. Align the CPU with the socket. The CPU has three bayonets (notches) that correspond to the socket. Carefully place the CPU into the socket, ensuring it sits flush without force.
4. Lower the wire buckle and secure it to lock the CPU in place. The black cover will pop up automatically.

Figure 3.1: Step-by-step guide for CPU installation.

Important CPU Handling Precautions:

• Do not open the CPU top cover.
• Do not touch the CPU pins to contact the core.
• Do not touch the motherboard interface pins.

Слика 3.2: Прample of normal vs. abnormal CPU socket pins. If abnormal, do not attempt repair; contact support.

3.2. Инсталација меморије (RAM)

The motherboard features two DDR3 Non-ECC memory slots. Ensure your memory modules are compatible with DDR3 1280/1333/1600/1866MHz frequencies.

1. Отворите копче на оба краја слота за меморију.
2. Поравнајте зарез на DDR3 меморијском модулу са кључем у слоту за меморију.
3. Чврсто притисните оба краја меморијског модула док се клипови не уклопе на своје место.

Figure 3.3: Location of DDR3 memory slots.

3.3. Инсталација уређаја за складиштење

The motherboard supports SATA M.2 (NGFF M.2) SSDs and traditional SATA 2.5-inch/3.5-inch drives.

3.3.1. NGFF M.2 SSD Installation

The SATA M.2 (NGFF M.2) interface supports AHCI protocol with transfer rates up to 6Gbps.

1. Locate the NGFF M.2 slot on the motherboard.
2. Уметните M.2 SSD у слот под благим углом.
3. Пажљиво притисните SSD и причврстите га приложеним завртњем.

Figure 3.4: SATA M.2 interface and compatible SSD.

3.3.2. Инсталација SATA диска

Connect your SATA hard drives or SSDs to the available SATA ports using SATA data cables. The motherboard includes one SATA 3.0 (6Gb/s) port and three SATA 2.0 (3Gb/s) ports.

Figure 3.5: Location of SATA 3.0 and SATA 2.0 ports.

3.4. Инсталација картице за проширење

The motherboard provides one PCIe 2.0 x16 slot, one PCIe 2.0 x1 slot, and one PCI slot for expansion cards such as graphics cards, sound cards, or network cards.

1. Align the expansion card with the desired slot.
2. Press down firmly until the card is fully seated in the slot and the retention clip (if present) engages.
3. Причврстите картицу за кућиште помоћу завртња.

Слика 3.6: Завршеноview of PCI and PCIe expansion slots.

3.5. Прикључци за напајање

Connect the 24-pin ATX power connector and the 4-pin ATX 12V CPU power connector from your power supply to the corresponding ports on the motherboard.

3.6. Конектори предње плоче

Connect the front panel cables (power button, reset button, HDD LED, power LED, USB ports, audio jacks) to their respective headers on the motherboard. Refer to the motherboard diagram for correct pin assignments.

4. Упутства за рад

4.1. Прво покретање и подешавање BIOS-а

Upon the first power-on after assembly, enter the BIOS setup utility to configure system settings. Typically, this is done by pressing the ДЕЛ or F2 key during the boot process. Configure boot order, date/time, and other necessary settings.

4.2. Инсталација драјвера

After installing your operating system, install the necessary drivers for the motherboard components (chipset, audio, LAN, USB 3.0). For Windows 10, many drivers may be automatically detected and installed. If manual installation is required, drivers can typically be found on the manufacturer's website or chipset vendor's website (e.g., Intel).

4.3. Integrated Graphics Output

The motherboard supports VGA and HDMI high-definition video output. Ensure your CPU has integrated graphics if you intend to use these ports without a dedicated graphics card. CPUs with an 'F' suffix (e.g., i5-xxxxF) do not have integrated graphics.

Figure 4.1: VGA and HDMI output interfaces.

5. Одржавање

Редовно одржавање помаже у обезбеђивању дуготрајности и стабилног рада ваше матичне плоче и компоненти рачунара.

• Уклањање прашине: Periodically clean dust from inside your PC case, especially from heatsinks and fans, using compressed air. Ensure the system is powered off and unplugged before cleaning.
• Управљање кабловима: Ensure cables are neatly routed to promote good airflow within the case.
• Ажурирања BIOS-а: Проверите произвођача website for BIOS updates. Only update the BIOS if necessary and follow the instructions carefully. Incorrect BIOS updates can damage the motherboard.
• Ажурирања софтвера: Редовно ажурирајте оперативни систем и управљачке програме како бисте осигурали компатибилност и оптималне перформансе.

КСНУМКС. Решавање проблема

Ако наиђете на проблеме након инсталирања матичне плоче, размотрите следеће кораке за решавање проблема:

• Без приказа/Без покретања:
  • Уверите се да су сви каблови за напајање (24-пински ATX, 4-пински CPU) безбедно повезани.
  • Reseat the memory modules. Try booting with only one memory stick if you have multiple.
  • Reseat the CPU. Check for any bent pins on the CPU socket (refer to Figure 3.2).
  • If using a dedicated graphics card, ensure it is properly seated and connected to power. Try connecting your monitor to the integrated graphics (VGA/HDMI) if your CPU supports it, to rule out the graphics card as the issue.
  • Clear the CMOS (Complementary Metal-Oxide-Semiconductor) by removing the CMOS battery for a few minutes or using the clear CMOS jumper (refer to motherboard diagram for location).
• Poor Contact Issues: If components like memory, CPU, or graphics card are not making proper contact, gently wipe the metal contacts with an eraser to improve conductivity.
• Проблеми са возачем: If you experience issues with network, audio, or other peripherals, ensure you have installed the correct and latest drivers. For Windows 10, many drivers are automatically installed.
• Нестабилност/падови система: Ensure your power supply unit (PSU) provides sufficient and stable power for all components. Check for proper cooling of the CPU and other components.

If problems persist after attempting these steps, it is recommended to seek professional assistance.

7. Подршка и гаранција

For technical support, driver downloads, or further assistance, please refer to the official MACHINIST website or contact their customer service channels. While a physical manual is not included with the product, this digital document serves as a comprehensive guide.

Информације о гаранцији: Specific warranty terms and conditions may vary. Please retain your proof of purchase for any warranty claims. For detailed warranty information, consult the product packaging or the official MACHINIST webсајту.

8. Производ је готовview Видео