Polivance 3701-4 Упутство за употребу премаза у боји за браник и облоге

1. Производ је готовview

The Polyvance Bumper & Cladding Color Coat (Model 3701-4) is an advanced, low-VOC, solvent-based coating specifically formulated to permanently recolor molded-in-color textured TPO and polypropylene plastic components. This includes bumpers, side cladding, and trim found on various vehicles.

Unlike temporary silicone-based products, this color coat adheres strongly to the plastic surface, providing a durable and lasting finish that resists fading, marring, and staining. It is designed for direct application without the need for adhesion promoters or extensive sanding on compatible plastic types.

Image 1.1: Polyvance 3701-4 Bumper & Cladding Color Coat in a quart can, showing product labeling and key features.

Кључне карактеристике:

• Permanently recolors faded, scuffed, marred, discolored, or damaged plastic bumpers, side cladding, and trim.
• Adheres to TPO and Polypropylene (PP) plastic without sanding, adhesion promoter, or primer.
• Forms a strong, durable bond that resists removal by pressure washing.
• Low VOC (Volatile Organic Compound) formula.

2. Безбедносне информације

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to ввв.П65Варнингс.ца.гов.

DANGER: FLAMMABLE. HARMFUL OR FATAL IF SWALLOWED. READ CAUTIONS ON BACK PANEL.

Always read and understand the Safety Data Sheet (SDS) for this product before use. The SDS provides detailed information on hazards, safe handling, and emergency procedures.

Опште мере предострожности:

• вентилација: Use in a well-ventilated area or outdoors. Avoid breathing vapors.
• Лична заштитна опрема (ЛЗО): Wear appropriate PPE, including chemical-resistant gloves, eye protection (safety goggles), and a respirator suitable for organic vapors.
• Запаљивост: Држати даље од топлоте, варница, отвореног пламена и врућих површина. Не пушити.
• Складиштење: Store in a cool, dry, well-ventilated place, away from incompatible materials and direct sunlight. Keep container tightly closed.
• одлагање: Одложите садржај и контејнер у складу са локалним, регионалним, националним и међународним прописима.
• Прва помоћ: In case of contact with skin or eyes, rinse immediately with plenty of water. If swallowed, do NOT induce vomiting. Call a Poison Control Center or doctor immediately.

3. Припрема и подешавање

Proper preparation of the surface is crucial for optimal adhesion and finish quality, even though sanding and adhesion promoters are not required for compatible plastics.

Површинска компатибилност:

• Препоручено: Molded-in-color textured TPO (Thermoplastic Olefin) and polypropylene (PP) plastic bumpers, side cladding, and trim.
• Not Recommended Without Sanding: Raw polyurethane (PUR) or OEM primed bumpers. These substrates require proper sanding and preparation before application.

Припремни кораци:

1. Очистите површину: Thoroughly clean the plastic surface to be coated. Use a suitable automotive cleaner or degreaser to remove all dirt, grease, wax, silicone, and other contaminants. Rinse thoroughly with water and allow to dry completely. Any residue will compromise adhesion.
2. маскирање: Mask off any areas not intended for coating, such as painted body panels, chrome trim, or adjacent components, using automotive masking tape and paper/plastic sheeting.
3. Температура и влажност: Ensure the application area is within recommended temperature and humidity ranges (refer to product label for specifics, typically room temperature and moderate humidity).
4. Добро протресите: Before opening, shake the can vigorously for at least 2-3 minutes to ensure the color coat is thoroughly mixed. Continue to shake periodically during application.

4. Application Instructions (Operating)

Follow these steps for effective application of the Polyvance Bumper & Cladding Color Coat:

1. Ventilation and PPE: Ensure adequate ventilation and wear all recommended personal protective equipment (gloves, eye protection, respirator).
2. Тестна област: If possible, test the color coat on an inconspicuous area or a scrap piece of the same plastic to verify color match and adhesion.
3. Начин примене: This product is typically applied using a spray gun. Consult the product label for specific nozzle and pressure recommendations. Apply in thin, even coats.
4. Први премаз: Apply a light, even mist coat to the prepared surface. This initial coat helps promote adhesion and provides a base for subsequent coats.
5. Subsequent Coats: Allow appropriate flash-off time between coats (refer to product label, typically 5-10 minutes). Apply additional thin, even coats until desired coverage and color uniformity are achieved. Avoid applying excessively thick coats, which can lead to runs or uneven drying.
6. Време сушења: Allow the coated surface to dry completely before handling or exposing to moisture. Drying times will vary based on temperature, humidity, and film thickness. Refer to the product label for specific recoat and full cure times.
7. Чишћење: Clean spray equipment immediately after use with appropriate solvent.

5. Одржавање

Once cured, the Polyvance Bumper & Cladding Color Coat provides a durable and permanent finish. Maintenance is straightforward:

• Чишћење: Clean the coated surface with standard automotive car wash soap and water. Avoid harsh abrasive cleaners or strong solvents, which could potentially damage the finish over time.
• Заштита: While the coating is highly durable, regular waxing or application of a UV protectant designed for automotive plastics can help extend its lifespan and maintain its appearance, especially in harsh environmental conditions.
• Damage Repair: In case of new damage (scratches, scuffs) to the coated area, the product can be reapplied to the affected section after proper cleaning and preparation.

КСНУМКС. Решавање проблема

This section addresses common issues that may arise during or after application.

7. Спецификације

8. Гаранција и подршка

Polyvance is committed to providing high-quality plastic repair products and expertise. While specific warranty details for the 3701-4 Bumper & Cladding Color Coat are not provided in this manual, customers are encouraged to contact Polyvance directly for any warranty-related inquiries or product support.

Polyvance has been assisting with plastic repairs since 1981 and focuses exclusively on products that aid in repairing or refinishing broken plastic. For technical assistance, application advice, or to report product issues, please refer to the contact information provided on the product packaging or the official Polyvance webсајту.

For more information about Polyvance and their commitment to quality, visit their official webсајту или се обратите њиховом одељењу за корисничку подршку.