1. Важне информације о безбедности
Пажљиво прочитајте сва упутства пре инсталације и употребе. Сачувајте ово упутство за будуће потребе.
- Напајање: This LED strip operates on 12В ДЦ. Connecting it to a higher voltage power source will damage the strip and may pose a fire hazard. Ensure your power supply is compatible and provides sufficient wattage for the length of the strip used. Power supply and controller are not included.
- Отпорност на воду: Овај производ има ИП30 оцена, што значи да јесте не-водоотпоран. Do not expose it to water, moisture, or high humidity. It is suitable for indoor use or protected outdoor environments where it will not come into contact with liquids.
- Сечење: The LED strip can be cut to desired lengths only at designated cutting marks, typically indicated by a copper pad and a scissor icon. Cutting elsewhere will damage the circuit and render that section unusable.
- Инсталација: Ensure the installation surface is clean, dry, and smooth for proper adhesion. Avoid bending the strip sharply, as this can damage the internal circuitry.
- Електричне везе: All electrical connections should be made securely to prevent short circuits or loose contacts. If you are unsure about wiring, consult a qualified electrician.
- Расипање топлоте: While LED strips generate minimal heat, ensure adequate ventilation, especially when installed in enclosed spaces, to prolong product lifespan.
2. Производ је готовview
The TOPXCDZ GS1903 Pixel LED Strip is a 5-meter addressable light tape featuring 60 LEDs per meter. It utilizes 5050SMD RGB LEDs with an external GS1903 chipset, allowing for individual control of every 3 LEDs (20 ICs per meter). This enables dynamic full-color effects such as chasing, scanning, and various dream color patterns. The strip operates on 12V DC and comes with a white PCB, 6mm width, and an IP30 non-waterproof rating.
Садржај пакета:
- 1 x 5-meter GS1903 Pixel LED Strip
Note: Power supply and LED controller are not included and must be purchased separately.
Слика 2.1: Детаљно view of the LED strip, highlighting the 5050SMD RGB LED chip, GS1903 IC (one IC controls three LEDs), safe resistor for stable voltage, and designated cutting points.
3. Спецификације
| Феатуре | Спецификација |
|---|---|
| ЛЕД извор | 5050SMD RGB External GS1903 chipset |
| ИЦ Типе | GS1903 (WS2811 compatible) |
| Воркинг Инпут Волtage | 12В ДЦ |
| Излазна снага | 0.2В по ЛЕД |
| Дриве Моде | Цонстант Волtage |
| ЛЕД количина | 60 LEDs/Meter (3 LEDs controlled by 1 IC) |
| Количина интегрисаног кола | 20 ICs/Meter |
| Пикелс | 20 Pixels/Meter |
| Граи Сцале | 256 |
| Боја | RGB (Full Color) |
| View Угао | 120° |
| Радна температура | -20°Ц до 60°Ц |
| Боја штампане плоче | White PCB |
| Водоотпорна оцена | ИП30 (није водоотпоран) |
| ПЦБ Видтх | 6мм |
| Снага (макс.) | 14В/метар |
| Контролни метод | App (via compatible controller) |
Image 3.1: LED strip dimensions and layout, indicating 60 LEDs/meter, 12V DC input, 6mm PCB width, and approximate 50mm segment length.
4. Подешавање и инсталација
4.1 Контролна листа пре инсталације:
- 12В ДЦ напајање: Ensure it provides sufficient current (Amps) for the total wattage of your LED strip. For a 5-meter strip at 14W/meter, you would need at least 70W (approx. 6A at 12V).
- Compatible LED Controller: An addressable LED controller (e.g., SP107E, SP110E, K-1000C, or similar WS2811/GS1903 compatible controller) is required to control the strip's effects.
- Ожичење: Appropriate gauge wires for connecting the strip to the controller and power supply.
- Чиста површина: The installation surface should be clean, dry, and free of dust or grease.
4.2 Кораци инсталације:
- Планирајте свој изглед: Determine the desired path for your LED strip. Measure and mark the installation area.
- Припремите површину: Clean the installation surface thoroughly. For optimal adhesion, use rubbing alcohol to remove any residues and let it dry completely.
- Cut the Strip (if necessary): If a shorter length is required, carefully cut the LED strip only at the designated cutting marks (copper pads with a scissor icon).
- Повежите се са контролером: Connect the LED strip to your compatible addressable LED controller. The strip typically has four wires: 12V (positive), GND (negative), DI (Data Input), и DO (Data Output). Connect these to the corresponding terminals on your controller.
- Повежите напајање: Connect the 12V DC power supply to your LED controller. Ensure correct polarity (positive to positive, negative to negative).
- Test Before Final Adhesion: Before peeling off the adhesive backing and permanently mounting the strip, connect all components and power them on to ensure the strip functions correctly.
- Монтирајте траку: Once tested, peel off the protective backing from the adhesive tape on the back of the LED strip and carefully press the strip onto the prepared surface. Apply firm, even pressure along the entire length.
Image 4.1: Connection points on the LED strip (12V, DO, DI, GND).
5. Упутство за употребу
The TOPXCDZ GS1903 Pixel LED Strip is an addressable LED product, meaning each segment of 3 LEDs can be controlled independently. To operate the strip and achieve various lighting effects, a compatible LED controller (not included) is required.
5.1 Using the LED Controller:
- Refer to the specific user manual provided with your LED controller for detailed instructions on its operation.
- Most controllers for GS1903/WS2811 strips offer control via a dedicated mobile application (App), remote control, or onboard buttons.
- Ensure your controller is set to the correct IC type (GS1903 or WS2811) and the correct number of pixels/LEDs to match your strip's configuration (20 pixels/meter, 60 LEDs/meter).
5.2 Common Functions (Controller Dependent):
- Избор боја: Choose from a wide spectrum of static colors.
- Динамички режими: Access various pre-programmed effects such as chasing, scanning, fading, flashing, and other 'dream color' patterns.
- Подешавање осветљености: Повећајте или смањите интензитет светлости.
- Контрола брзине: Подесите брзину динамичких светлосних ефеката.
- Прилагођавање: Some advanced controllers allow for custom pattern creation and sequencing.
Слика 5.1: Примерample of dynamic RGB lighting effects achievable with the LED strip.
Image 5.2: Further illustration of the diverse lighting patterns.
6. Одржавање
Правилно одржавање осигурава дуготрајност и оптималне перформансе ваше ЛЕД траке.
- Чишћење: Gently wipe the surface of the LED strip with a soft, dry, lint-free cloth to remove dust. Do not use abrasive cleaners, solvents, or excessive moisture.
- Провера везе: Periodically inspect all electrical connections to ensure they are secure and free from corrosion. Loose connections can lead to flickering or intermittent operation.
- Физички преглед: Check the strip for any signs of physical damage, such as cracks, tears, or exposed wiring. If damage is found, discontinue use and replace the affected section or the entire strip.
- Услови животне средине: Ensure the strip remains within its specified operating temperature range (-20°C to 60°C) and is not exposed to moisture, as it is non-waterproof (IP30).
КСНУМКС. Решавање проблема
Ако наиђете на проблеме са ЛЕД траком, погледајте следеће уобичајене проблеме и решења:
| Проблем | Могући узрок | Решење |
|---|---|---|
| ЛЕД трака не светли. | Нема струје, нетачна јачина звукаtage, loose connections, faulty controller, damaged strip. | Verify 12V DC power supply is connected and working. Check all wiring connections (12V, GND, DI). Ensure the controller is powered on and functioning. Test with a known good controller if possible. Inspect the strip for visible damage. |
| Incorrect colors or patterns. | Controller settings incorrect, data wire (DI) connected to wrong pin, faulty controller. | Check your LED controller's settings to ensure the correct IC type (GS1903/WS2811) and pixel count are selected. Verify the DI wire is connected to the data output of the controller. |
| Only a section of the strip is not working. | Damaged segment, improper cut, loose connection at a cut point. | Inspect the non-working section for physical damage. If the strip was cut, ensure the connections at the cut point are secure and properly soldered (if applicable). |
| ЛЕД диоде трепере или су пригушене. | Insufficient power supply, loose connections, voltage drop over long runs, faulty controller. | Ensure your 12V DC power supply has enough wattage/current for the entire strip. Check all connections for tightness. For very long runs, consider injecting power at multiple points or using thicker gauge wires. |
| Strip gets excessively hot. | Оверволtage, poor ventilation, short circuit. | Immediately disconnect power. Verify the power supply is 12V DC. Ensure the strip is not covered or installed in an enclosed space without airflow. Check for any visible short circuits. |
8. Гаранција и подршка
This product is manufactured to high-quality standards. For any questions, technical assistance, or warranty claims, please contact the seller or manufacturer directly through your purchase platform. Please have your order number and product model (GS1903 Pixel LED Strip) ready when contacting support.