1. Увод
This manual provides instructions for the installation, operation, and maintenance of the Sensor Switch WSXA-PDT-WH Occupancy Motion Sensor Switch. This device is designed to automatically control lighting based on occupancy detection, utilizing dual technology for enhanced reliability.
2. Безбедносне информације
WARNING: RISK OF ELECTRIC SHOCK. Improper installation can lead to serious injury or death.
- Инсталацију мора да изврши квалификовани електричар у складу са свим националним и локалним електричним прописима.
- Disconnect power at the circuit breaker or fuse before installing or servicing the switch.
- Do not install with wet hands or while standing on wet or damp површине.
- Уверите се да су сви жичани спојеви безбедни и правилно изоловани.
- Овај уређај је само за унутрашњу употребу.
3. Садржај пакета
Пре почетка инсталације проверите да ли су све компоненте присутне:
- Sensor Switch WSXA-PDT-WH Occupancy Motion Sensor Switch (White)
- Монтажни завртњи
- Жичане матице
- Упутство за употребу (овај документ)
4. Подешавање
4.1 Пре-инсталација
- Искључите напајање: Locate the circuit breaker or fuse box controlling the light switch you are replacing. Turn off the power completely. Verify power is off using a voltagе тестер.
- Уклоните постојећи прекидач: Пажљиво уклоните зидну плочу и одврните постојећи прекидач из зидне кутије. Искључите жице.
4.2 Упутства за ожичење
The WSXA-PDT-WH switch requires specific wiring connections. Refer to the diagram below for typical wiring. If you are unsure, consult a qualified electrician.
Note: The WSXA-PDT-WH is designed for 120/277VAC applications.
- Црна жица: Connect to the incoming Линија (вруће) жице.
- Црвена жица: Повежите се на Учитај wire (to the light fixture).
- Бела жица: Повежите се на Неутрално жице.
- зелена жица: Повежите се на Гроунд жице.
4.3 Монтажа
- After wiring, carefully push the switch into the wall box.
- Secure the switch to the wall box using the provided mounting screws.
- Attach the wall plate (not included) over the switch.
4.4 Почетно укључивање
- Вратите напајање на прекидач.
- The sensor will enter a warm-up period (typically 30-60 seconds) during which the lights may cycle on and off.
- After the warm-up, the sensor will begin normal operation.
5. Упутство за употребу
The WSXA-PDT-WH is a Dual-Tech occupancy sensor switch, combining Passive Infrared (PIR) and Ultrasonic technologies for reliable motion detection.
5.1 Automatic On/Off Operation
- When occupancy is detected, the switch will automatically turn on the connected lights.
- The lights will remain on as long as occupancy is detected.
- After the set time delay expires and no occupancy is detected, the lights will automatically turn off.
5.2 Ручно пребацивање
Most models include a push-button for manual control:
- Press to turn ON/OFF: A quick press of the button will toggle the lights on or off, overriding the sensor's automatic function temporarily.
- Hold for specific functions: Refer to the detailed programming guide for advanced settings accessible via button presses (e.g., adjusting time delay, sensitivity).
5.3 Подешавање подешавања
The WSXA-PDT-WH typically features adjustable settings for optimal performance. These adjustments are usually made via small dials or dip switches located behind the wall plate or on the device itself.
- Временско кашњење: Controls how long the lights remain on after the last detected motion. Common settings range from 30 seconds to 30 minutes.
- Осетљивост: Adjusts the detection range for both PIR and Ultrasonic sensors. Higher sensitivity detects smaller movements or movements further away.
- Ambient Light Sensor (ALS): Prevents lights from turning on if there is sufficient natural light in the room. This can be enabled or disabled, and the light level threshold may be adjustable.
Consult the full programming guide for detailed instructions on accessing and adjusting these settings.
6. Одржавање
The Sensor Switch WSXA-PDT-WH requires minimal maintenance to ensure optimal performance.
- Чишћење: Periodically wipe the sensor lens with a soft, dry cloth to remove dust or debris. Do not use abrasive cleaners or solvents.
- Препреке: Ensure that the sensor's detection area is not obstructed by furniture, curtains, or other objects that could block motion detection.
- Повер Цицлинг: If the sensor appears to be malfunctioning, try turning off the power at the circuit breaker for 30 seconds, then restoring it. This can reset the device.
КСНУМКС. Решавање проблема
If you experience issues with your WSXA-PDT-WH sensor switch, refer to the following common problems and solutions:
| Проблем | Могући узрок | Решење |
|---|---|---|
| Светла се не пале. | No power; incorrect wiring; ambient light sensor active; sensor obstructed; bulb burned out. | Check circuit breaker; verify wiring; adjust ambient light sensor setting; clear obstructions; replace bulb. |
| Lights turn off too quickly. | Time delay set too short; insufficient motion detected; sensor obstructed. | Increase time delay setting; ensure clear line of sight for sensor; adjust sensitivity. |
| Светла се не гасе. | Constant motion detected; time delay set too long; faulty sensor. | Ensure no constant motion in detection area; reduce time delay setting; contact support if issue persists. |
| Lights flicker or cycle. | Loose wiring; incompatible load; electrical interference. | Check all wire connections; ensure load is within specifications; consult electrician. |
If troubleshooting steps do not resolve the issue, contact Sensor Switch technical support.
8. Спецификације
| Феатуре | Детаљ |
|---|---|
| Број модела | WSXA-PDT-WH |
| Бранд | Прекидач сензора |
| Боја | Бела |
| Извор напајања | Цордед Елецтриц |
| Волtage | 120/277 волти наизменичне струје |
| Ватtage | 800-Watt (120V) |
| Тип монтаже | Валл Моунт |
| Технологија | Dual Technology (PIR & Ultrasonic) |
| Димензије производа | 4.3 к 1.8 к 1.8 инча |
| Тежина артикла | 5.5 унци |
| Компатибилни уређаји | Light, Fan, Smart Home Systems |
| УПЦ | 194994625827 |
9. Гаранција и подршка
Sensor Switch products are designed for reliability and performance. For specific warranty details, please refer to the warranty card included with your product or visit the official Sensor Switch webсајту.
For technical support, product inquiries, or warranty claims, please contact Sensor Switch customer service through their official channels. Have your model number (WSXA-PDT-WH) and purchase information ready when contacting support.