Flysky FS-IA10B 10-Channel 2.4GHz AFHDS 2A RC Receiver User Manual

1. Увод

The Flysky FS-IA10B is a 10-channel 2.4GHz AFHDS 2A (Automatic Frequency Hopping Digital System Second Generation) receiver designed for various remote-controlled models, including airplanes, gliders, and helicopters. This manual provides essential information for the proper setup, operation, and maintenance of your FS-IA10B receiver.

Молимо вас да пажљиво прочитате ово упутство пре употребе пријемника како бисте осигурали безбедан и ефикасан рад.

2. Садржај пакета

• 1 x Flysky FS-IA10B 10-Channel Receiver
• 1 x Bind Cable

3. Карактеристике

• 2.4GHz 10-Channel: Utilizes the second-generation automatic digital frequency system (AFHDS 2A) for reliable communication.
• Компатибилни предајници: Works with Flysky FS-i4, FS-i6, FS-i6S, FS-i6X, FS-i10, FS-GT2E, FS-GT2F, FS-GT2G, FS-it4S, FS-GT5, FS-i8, FS-TM10 transmitters.
• Применљиви модели: Suitable for RC airplanes, gliders, and helicopters.
• Dual Antenna: Features two 26mm antennas for enhanced radio frequency signal reception and reliability.
• ЛЕД индикатор: A light indicator displays the receiver's power and operational status in real-time.
• Интерфејси података: Supports PWM, PPM, i.bus, and s.bus data connections.
• RSSI Support: Provides Received Signal Strength Indication.

4. Спецификације

The receiver is shown held in a hand for scale, with dimensions indicated as 5cm (length), 3.2cm (width), and 1.5cm (height).

5. Подешавање и повезивање

The FS-IA10B receiver must be bound to your Flysky transmitter before use. Follow these steps carefully:

1. Припремите предајник: Install the battery in your 2.4G Flysky transmitter and ensure it is turned OFF.
2. Повежите кабл за повезивање: Insert the bind cable (included) into the BIND/CH3 channel port of the FS-IA10B receiver.
3. Power Receiver: Connect the receiver battery (not included) to the VCC port of the receiver. Both LEDs on the receiver will flash simultaneously, indicating the receiver is in binding mode.
4. Покрени везивање на предајнику: Press and hold the bind button on your transmitter, then power on the transmitter.
5. Observe Receiver LED: Observe the LED on the receiver. When the LED stops flashing and remains solid, it indicates successful binding. This process typically takes about 5 seconds.
6. Комплетно везивање: Release the bind button on the transmitter and remove the bind cable from the receiver.
7. Тест систем: Install the servos and other components, then perform a thorough test of all functions. If testing fails, please repeat the above steps. If testing is successful, binding is complete.

Важна напомена: Do not power on the receiver during the setup process to prevent loss of control. The binding procedure described above is only applicable to Flysky 2.4G products.

This diagram provides guidance on proper antenna orientation (90-degree angles) for optimal signal reception and a detailed wiring schematic connecting the receiver to a bind cable, battery, switch, and various servos (Rudder, Throttle, Elevator, Aileron) via i-BUS and PPM/CHT interfaces.

This image visually outlines the seven steps for binding the receiver to a transmitter, including connecting the bind cable, battery, and observing the LED indicator for successful pairing.

6. Упутство за употребу

Once the receiver is successfully bound to your transmitter and installed in your model, ensure all connections to servos, flight controllers, or other components are secure. Power on your transmitter first, then power on your model (receiver). Always verify that all control surfaces and functions respond correctly to transmitter inputs before flight or operation.

This image shows the Flysky FS-IA10B receiver from a top-down perspective, highlighting its dual antennas and clearly labeled ports for channels (CH1-CH10), PPM/CHT, i-BUS, SENS, SERVO, and B/VCC.

Детаљно view of the receiver's port pins, indicating the standard S (Signal), + (Positive), and - (Negative) connections for each channel.

7. Одржавање

• Држите пријемник чистим и без прашине, прљавштине и влаге.
• Редовно проверавајте све ожичење и спојеве да ли постоје знаци хабања или оштећења.
• Ensure antennas are not bent or damaged and are positioned correctly for optimal signal reception.
• Чувајте пријемник на сувом и хладном месту када га не користите.

КСНУМКС. Решавање проблема

• Receiver not binding: Ensure the transmitter is a compatible Flysky 2.4G model. Verify that the bind cable is correctly inserted into the BIND/CH3 port and that the receiver battery is providing adequate power. Repeat the binding steps carefully.
• No signal/intermittent signal: Check antenna placement and ensure they are not obstructed or damaged. Verify that the transmitter and receiver are within range and that there are no major sources of interference nearby.
• Incorrect servo response: Confirm that servos are correctly plugged into the appropriate channels on the receiver. Check transmitter settings for channel assignments and servo directions.
• ЛЕД диода се не пали: Check the power connection to the receiver. Ensure the battery is charged and connected correctly to the VCC port.

9. Безбедносне информације

• Always operate RC equipment responsibly and in accordance with local laws and regulations.
• Ensure your model is safe to operate and all components are functioning correctly before each use.
• Keep a safe distance from people, animals, and property when operating RC models.
• Never operate RC equipment near power lines, busy roads, or airports.
• Disconnect the battery from the model when not in use to prevent accidental activation.

10. Гаранција и подршка

За информације о гаранцији и техничку подршку, погледајте документацију коју сте добили уз куповину или контактирајте продавца. Сачувајте доказ о куповини за евентуалне рекламације у оквиру гаранције.