1. Упутства за подешавање
1.1 Шта је укључено
- Two (2) Bio Bidet SlimEdge Bidet Attachments
- T-Valve with rubber washer
- Биде Хосе
- Монтажни носачи
- Toilet Seat Bumpers (optional)
1.2 Потребан алат
- Подесиви кључ
- Screwdriver (for toilet seat screws)
- Towel (for catching residual water)
1.3 Контролна листа пре инсталације
- Ensure you have access to the toilet's water supply valve.
- Confirm your toilet seat is removable.
- Прочитајте сва упутства пре почетка инсталације.
1.4 Кораци инсталације
Follow these steps to install your Bio Bidet SlimEdge attachment. No plumber is necessary for this simple DIY installation.
Official Bio Bidet installation video demonstrating the process of attaching the bidet to a toilet.
- Turn off Water Supply and Remove Toilet Seat: Locate the water supply valve behind your toilet and turn it clockwise to shut off the water. Flush the toilet to drain the tank. Remove your existing toilet seat by unscrewing the bolts at the back.
Image illustrating the first step of installation: turning off the water supply and removing the toilet seat.
- Connect the T-Valve: Disconnect the water supply hose from the toilet tank. Ensure the rubber washer is properly seated inside the T-valve. Attach the T-valve to the toilet tank fill valve. Reattach your original water supply line to the bottom of the T-valve.
Image showing the connection of the T-valve to the toilet tank's fill valve.
- Place the Bidet Attachment: Position the SlimEdge bidet attachment on your toilet bowl, aligning the mounting brackets with the toilet seat bolt holes. Adjust the brackets to ensure the bidet is centered.
Image demonstrating the correct placement of the bidet attachment on the toilet bowl.
- Secure Toilet Seat: Reinstall your toilet seat over the bidet attachment and secure it using the original bolts. If necessary, use the included toilet seat bumpers to prevent any gap or wobble.
Image illustrating the reinstallation of the toilet seat over the bidet attachment.
- Connect Bidet Hose: Connect one end of the provided bidet hose to the T-valve and the other end to the inlet on the side of the bidet attachment. Hand-tighten all connections, then use an adjustable wrench for a quarter-turn to ensure a secure, leak-free fit.
- Обнова снабдевања водом: Slowly turn the water supply valve counter-clockwise to restore water flow to the toilet and bidet. Check all connections for leaks.
2. Упутство за употребу
The Bio Bidet SlimEdge features a simple comfort control knob for easy operation.
Image showing the comfort control knob for adjusting water pressure and selecting wash modes.
2.1 Water Pressure Adjustment
- The comfort control knob allows you to adjust the water pressure.
- Turn the knob gradually to increase or decrease the water pressure to your desired comfort level.
2.2 Nozzle Functions (Front/Rear Wash)
The SlimEdge is equipped with dual nozzles for targeted cleaning.
Image displaying the retractable dual nozzles of the bidet attachment.
- Прање задњег дела: Turn the comfort control knob towards the 'Rear Wash' setting for posterior cleaning.
- Женско прање: Turn the comfort control knob towards the 'Front Wash' setting for a gentler, feminine wash.
- The nozzles retract automatically when the water is turned off.
3. Одржавање
3.1 Cleaning the Nozzles
- To clean the nozzles, gently pull them out manually.
- Use a soft brush and mild soap to clean the nozzle tips.
- Rinse thoroughly with water and push them back into their retracted position.
3.2 Генерално чишћење
- Wipe the exterior of the bidet attachment with a soft, damp крпом и благим, неабразивним средством за чишћење.
- Avoid using harsh chemicals or abrasive cleaning tools, as these can damage the finish.
3.3 Зимовање
As a non-electric bidet, the SlimEdge does not require complex winterization procedures. However, if the bidet is installed in an unheated area where temperatures may drop below freezing, it is recommended to:
- Shut off the water supply to the bidet.
- Disconnect the bidet hose and drain any remaining water from the bidet and hose to prevent freezing and potential damage.
КСНУМКС. Решавање проблема
| Иссуе | Могући узрок | Решење |
|---|---|---|
| Цурење воде | Loose connections, missing/damaged washer | Ensure all connections are hand-tightened, then use a wrench for a quarter-turn. Check that all washers are correctly installed. |
| Нема протока воде | Water supply valve is closed, bidet hose kinked | Open the water supply valve fully. Check the bidet hose for any kinks or obstructions. |
| Weak Water Spray | Partially closed water supply, clogged nozzles | Ensure the water supply valve is fully open. Clean the nozzles as described in the Maintenance section. |
| Toilet Seat Wobbles | No bumpers or incorrect bumper placement | Install or adjust the included toilet seat bumpers to provide stable support for the toilet seat. |
5. Спецификације
| Феатуре | Детаљ |
|---|---|
| Произвођач | Bio Bidet |
| Број модела | SlimEdge 2-Pack |
| Тежина артикла | 5.59 фунти |
| Димензије производа | 18 к 10 к 4 инча |
| Величина | 2 Пацк |
| Боја | Бела |
| Стиле | Comfort Control Knob |
| Материјал | Пластика |
| Укључене компоненте | (2) bidet attachments |
| Батерије су потребне? | бр |
6. Гаранција и подршка
6.1 Информације о гаранцији
Manufacturer warranty covers US and Canada customer purchases for 1 year from the date of purchase. Please retain your proof of purchase for warranty claims.
6.2 Корисничка подршка
For any questions regarding installation, operation, maintenance, or troubleshooting, please contact Bio Bidet customer support. Refer to the product packaging or the official Bio Bidet webсајт за најновије контакт информације.