OurLeeme 12V 1100 GPH Automatic Bilge Pump Instruction Manual

1. Увод

This manual provides essential information for the safe and efficient operation of your OurLeeme 12V 1100 GPH Automatic Bilge Pump. Please read these instructions carefully before installation and use, and retain them for future reference.

Карактеристике производа:

• Мала потрошња енергије: Highly efficient with very low energy usage and high capacity.
• Компактна величина: Small, lightweight design, space-saving, quiet operation, and low vibration.
• Висока брзина протока: Provides a large water output for rapid water evacuation.
• Потпуно аутоматски рад: Equipped with an integrated electronic Reed sensor system for easy, fully automatic control.
• Водоотпорни дизајн: Fully submersible and fire-resistant with anti-airlock design and moisture-tight seals.
• Издржљива конструкција: Stainless steel shaft, impact-resistant plastic housing with anti-rust and corrosion-resistant properties.
• Заштита од рада на суво: Designed not to burn out when running dry.
• Разноврсна употреба: Compatible with both fresh and saltwater.

Figure 1: OurLeeme 12V 1100 GPH Automatic Bilge Pump. This image shows the compact design of the bilge pump with its white and blue casing and integrated wiring.

2. Безбедносне информације

Please observe the following safety warnings to prevent injury or damage to the product.

Figure 2: Product Warning Label. This label indicates a choking hazard due to small parts, making it unsuitable for children under 3 years old. It also displays CE and UKCA compliance marks.

• Опасност од гушења: Contains small parts. Keep away from children under 3 years of age.
• Ensure all electrical connections are properly insulated and protected from water ingress.
• Do not operate the pump if the wiring is damaged.
• Увек искључите напајање пре него што извршите било какво одржавање или инсталацију.
• Ова пумпа је намењена само за пумпање воде. Не користите је за запаљиве течности, хемикалије или друге опасне материјале.

3. Садржај пакета

Проверите да ли су све ставке присутне у пакету:

• 1 к ОurLeeme 12V 1100 GPH Automatic Bilge Pump

4. Спецификације

Figure 3: Product Dimensions. This image illustrates the length (14.5 cm / 5.7"), width (7.8 cm / 3.1"), and height (10 cm / 3.9") of the bilge pump.

5. Инсталација и подешавање

Правилна инсталација је кључна за перформансе и дуготрајност пумпе.

Монтажа:

• Position the pump in the lowest part of the bilge or desired water collection area.
• Ensure the pump is securely mounted to prevent movement during operation.
• The pump is fully submersible.

Прикључак црева:

• Connect a 0.75-inch (19mm) discharge hose to the pump's outlet.
• Причврстите црево цревом цлamp за спречавање цурења.
• Route the discharge hose upwards and overboard, ensuring a continuous downward slope to prevent backflow.

Figure 4: Typical Bilge Pump Installation. This image shows the bilge pump positioned within a boat's bilge, ready for operation.

6. Упутства за ожичење

Correct wiring is essential for safe and automatic operation. Always disconnect the power source before wiring.

Идентификација жице:

• Црна жица: Connect to the negative (-) terminal of the 12V power source.
• Црвена жица: Connect to the positive (+) terminal for Мануал Моде операција.
• Плава жица: Connect to the positive (+) terminal for Аутоматски режим операција.

Figure 5: Wiring Details. This close-up shows the black (negative), red (manual positive), and blue (automatic positive) wires emerging from the pump.

Дијаграм ожичења:

Before wiring, open the filter and remove the foam block located under the float mechanism.

Figure 6: Wiring Diagram. This diagram illustrates connections for both Automatic Mode (Black to Battery -, Blue to Battery +) and Manual Mode (Black to Battery -, Red to Battery +). Note: The diagram shows a "Brown" wire for manual mode, but the product description and other images indicate "Red" for manual positive connection. Please follow the Red wire for manual positive connection as per the product description and Figure 5.

• Аутоматски режим: Повежите Црно wire to the battery's negative terminal. Connect the Плава wire to the battery's positive terminal. The pump will activate automatically when the water level rises.
• Ручни режим: Повежите Црно wire to the battery's negative terminal. Connect the Црвени wire to the battery's positive terminal. The pump will operate continuously as long as power is supplied.
• It is recommended to install a fuse (not included) in the positive line for circuit protection.

7. Упутство за употребу

Тхе ОurLeeme Bilge Pump offers both automatic and manual operation modes.

Аутоматски рад:

• When wired for Automatic Mode (Blue wire to positive), the pump's internal float switch will detect rising water levels.
• The pump will automatically activate when the water reaches a critical level.
• Once the water level drops below the sensor, the pump will automatically shut off.

Figure 7: Automatic Operation Cycle. This sequence illustrates how the pump activates when water reaches a critical level and deactivates once the water is pumped out and the level drops.

Ручни рад:

• When wired for Manual Mode (Red wire to positive), the pump will run continuously as long as power is supplied.
• This mode is suitable for situations requiring continuous pumping or for testing the pump.
• Always monitor the pump during manual operation to prevent dry running for extended periods, although the pump is designed not to burn out when dry.

8. Одржавање

Regular maintenance ensures optimal performance and extends the lifespan of your bilge pump.

• Редовно прегледајте: Periodically check the pump for debris, such as leaves, hair, or other foreign objects that may obstruct the intake or impeller.
• Очистите усисни екран: The pump features a removable filter/intake screen. Clean it regularly to ensure unrestricted water flow.
• Проверите ожичење: Inspect all wiring connections for corrosion, fraying, or loose terminals. Ensure connections are secure and waterproof.
• Пробни рад: Regularly test the pump's automatic and manual functions to confirm it is operating correctly. For automatic mode, introduce water into the bilge to trigger the float switch.
• Зимљење: In freezing conditions, ensure the pump is drained and protected from ice formation, or remove it for storage.

КСНУМКС. Решавање проблема

If you encounter issues with your bilge pump, refer to the following common problems and solutions:

10. Гаранција и подршка

Specific warranty information is not provided in the product details. For warranty claims or technical support, please contact your retailer or the manufacturer, OurLeeme, directly. Keep your purchase receipt as proof of purchase.