Einaus 2-Channel Universal Wireless Radio Receiver Instruction Manual

1. Увод

This instruction manual provides detailed guidance for the installation, setup, and operation of your Einaus 2-Channel Universal Wireless Radio Receiver. This device is designed for wireless control of various electrical appliances, including heaters, ventilation systems, air conditioners, pumps, barriers, lighting, multi-channel electric doors and windows, electronic locks, garage doors, lifting equipment, and industrial automation systems. Please read this manual thoroughly before use to ensure proper function and safety.

2. Садржај пакета

Након отварања пакета, требало би да пронађете следеће компоненте:

• 1 x Receiver module with protective casing
• 2 x Remote controls (each with battery installed)

Ако неке компоненте недостају или су оштећене, обратите се корисничкој подршци.

3. Спецификације

4. Производ је готовview

5. Подешавање и упаривање

5.1. Clearing Existing Codes

To clear all previously paired remote controls from the receiver's memory:

1. Лоцирајте Дугме за учење on the receiver board.
2. Притисните и држите Дугме за учење until the indicator light turns off. This indicates that all stored codes have been successfully cleared.

5.2. Pairing a Remote Control (Learning Mode)

To pair a new remote control with the receiver:

1. Притисните тастер Дугме за учење on the receiver once. The indicator light will flash once and then turn off. This signifies the receiver is ready to learn a new code in Momentary mode.
2. Immediately press any button on your remote control. The indicator light on the receiver will flash to confirm successful pairing.
3. Repeat for additional remote controls if needed.

6. Радни режими

The receiver supports several operating modes, which determine how the relay responds to remote control input. You can set the desired mode by pressing the Дугме за режим on the receiver board a specific number of times.

6.1. Тренутни режим

In Momentary mode, the relay activates only as long as the remote control button is pressed. Releasing the button deactivates the relay.

• Подешавање: Притисните тастер Дугме за режим once. The indicator will flash once and turn off.

6.2. Latch Mode

In Latch mode, one button press activates the relay, and another distinct button press is required to deactivate it.

• Подешавање: Притисните тастер Дугме за режим twice. The indicator will flash twice and turn off.

6.3. Пребаци режим

In Toggle mode, a single button press activates the relay, and pressing the same button again deactivates it. It acts like a flip-flop switch.

• Подешавање: Притисните тастер Дугме за режим three times. The indicator will flash three times and turn off.

6.4. 5-Second Delay Mode

This mode activates the relay for a fixed duration of 5 seconds after a button press, then automatically deactivates it.

• Подешавање: Притисните тастер Дугме за режим four times. The indicator will flash four times and turn off.

7. Схеме ожичења

The following diagrams illustrate common wiring configurations for the Einaus 2-Channel Universal Wireless Radio Receiver. Always ensure power is disconnected before making any wiring changes.

8. Одржавање

The Einaus Wireless Radio Receiver is designed for reliable operation with minimal maintenance. Follow these guidelines to ensure longevity:

• Чишћење: Keep the receiver free from dust and debris. Use a soft, dry cloth for cleaning. Do not use liquid cleaners or solvents.
• Окружење: Ensure the receiver is installed in a dry environment, away from direct moisture, extreme temperatures, and corrosive substances.
• Напајање: Use a stable power supply within the specified voltagе опсег (ДЦ 12-48В).
• Батерије за даљински управљач: Replace remote control batteries when their range decreases or they stop responding.

КСНУМКС. Решавање проблема

If you encounter issues with your receiver, refer to the following troubleshooting steps:

• Пријемник не одговара:
  • Check the power supply to the receiver. Ensure it is within the 12-48V DC range and properly connected.
  • Проверите да батерије даљинског управљача нису празне.
  • Ensure the remote control is paired correctly. Try re-pairing the remote control (refer to Section 5.2).
  • Check for strong radio interference in the vicinity.
• Short Operating Range:
  • Замените батерије даљинског управљача.
  • Ensure there are no significant obstructions (thick walls, metal structures) between the remote and the receiver.
  • Avoid installing the receiver near large metal objects or other radio-emitting devices.
• Релеј се не активира/деактивира:
  • Check the wiring to the load. Ensure connections are secure and correct according to the wiring diagrams (Section 7).
  • Verify the operating mode is set as intended (Section 6).
  • Ensure the load current does not exceed the maximum 10A rating.

Ако проблем и даље постоји након што сте пратили ове кораке, обратите се корисничкој подршци.

10. Гаранција и подршка

This Einaus product is covered by a standard manufacturer's warranty against defects in materials and workmanship. Please refer to your purchase documentation for specific warranty terms and duration.

For technical support, troubleshooting assistance, or warranty claims, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.