WONDOM ADAU1701 DSP Preamp: 2-In 4-Out Digital Signal Processor Instruction Manual

Увод

This manual provides detailed instructions for the installation, operation, and maintenance of your WONDOM ADAU1701 DSP Preamp. This unit is designed for advanced audio signal processing, offering a 2-input, 4-output configuration with digital crossover capabilities and support for SigmaStudio programming.

Кључне карактеристике укључују:

• Powered by ADAU1701 DSP, a 28/56bit Digital Signal Processor Engine.
• 24bit ADC/DAC Resolution Ratio with a 48kHz Sampлинг Рате.
• Unbalanced 2-Input, 4-Output Preamp Јединица.
• USB Type-C Port for DC 5V Power.
• Four Potentiometers for High-Pass Filter (HPF), Low-Pass Filter (LPF), and Volume Control.
• Integrated Mute & Phase Switches.
• Supports SigmaStudio Programming when connected with an ICP5 programmer.
• Open-sourced Demo Program & HEX Files are provided for restoring factory settings.

Садржај пакета

Молимо вас да проверите да ли су све ставке присутне у пакету:

• WONDOM ADAU1701 DSP Preamp Јединица
• USB Type-C Cable (for power)
• Кориснички приручник (овај документ)
• (Optional: ICP5 Programmer, sold separately for advanced programming)

Безбедносне информације

• Ensure the power supply matches the device's requirements (DC 5V, 1A via USB Type-C).
• Не излажите уређај влази или екстремним температурама.
• Avoid opening the enclosure unless you are a qualified technician.
• Чувати ван домашаја деце.

Сетуп

1. Физичке везе

Refer to the diagrams below for proper connection of audio inputs, outputs, and power.

Слика 1: Прикључци на задњој плочи. This image shows the rear panel of the ADAU1701 DSP Preamp, highlighting the DC Input (5V, 1A), ICP Port, Line In (ADC0 Left, ADC1 Right), and Line Out (DAC0 Right, DAC1 Left, DAC2 Right, DAC3 Left) RCA jacks.

• Прикључак за напајање: Connect a DC 5V, 1A power supply to the USB Type-C port labeled "DC INPUT 5V, 1A" on the rear panel.
• Аудио улаз: Connect your audio source (e.g., media player, pre-amplifier) to the "LINE IN" RCA jacks (ADC0 Left, ADC1 Right).
• Аудио излаз: Повежите своје amplifiers or powered speakers to the "LINE OUT" RCA jacks. The default configuration provides 2-channel mid-range output (DAC2 Right, DAC3 Left) and 2-channel bass output (DAC0 Right, DAC1 Left) for a 2-way digital crossover setup.
• ICP Port: This port is used for connecting an ICP5 programmer (sold separately) for advanced SigmaStudio programming.

2. Прво укључивање

Once all connections are secure, apply power to the unit. The "POWER" LED on the front panel should illuminate, indicating the device is operational.

Упутство за употребу

The WONDOM ADAU1701 DSP Preamp features several controls on its front panel for direct adjustment, as well as advanced programming capabilities via SigmaStudio.

Figure 2: Front Panel Controls. This image displays the front panel, showing the Power LED, Busy LED, SW1 (Mute) and SW2 (Phase) switches, and four potentiometers (POT1, POT2, POT3, POT4) for various audio adjustments.

Контроле на предњој плочи:

• ПОВЕР ЛЕД: Означава да је уређај укључен.
• BUSY LED: Indicates DSP activity.
• SW1 (Mute Switch): Toggles audio output mute on/off.
• SW2 (Phase Switch): Adjusts the phase of the audio output.
• POT1 (MP3 / ADC2): Controls the High-Pass Filter (HPF) for Bank B (3kHz-20kHz).
• POT2 (MP8 / ADC3): Controls the Low-Pass Filter (LPF) for Bank A (210Hz-3kHz).
• POT3 (MP9 / ADC0): Controls the High-Pass Filter (HPF) for Bank A (10Hz-310Hz).
• POT4 (VOL): Контролише укупну јачину звука.

Digital Crossover Configuration:

The unit's default output is configured as a 2-way digital crossover, providing dedicated outputs for bass and mid-range frequencies.

Figure 3: 2-In, 4-Out Digital Crossover. This diagram shows the RCA jack assignments for 2-channel Line Input, 2-channel Mid-range Output, and 2-channel Bass Output, facilitating a 2-way digital crossover setup.

• 2CH Line Input: ADC0 Left (White), ADC1 Right (Red).
• 2CH Mid-range Output: DAC2 Right (Red), DAC3 Left (White).
• 2CH Bass Output: DAC0 Right (Red), DAC1 Left (White).

SigmaStudio Programming:

For advanced customization and fine-tuning of the DSP functions, the unit supports programming via Analog Devices' SigmaStudio software. An ICP5 programmer (sold separately) is required to connect the DSP unit to your computer.

Figure 4: SigmaStudio Programming Setup. This image illustrates the connection between the DSP unit and an ICP5 programmer, along with a visual representation of the SigmaStudio graphical programming interface.

• софтвер: Download and install SigmaStudio from the Analog Devices webсајту.
• хардвер: Connect the ICP5 programmer to the ICP Port on the DSP unit and to your computer via USB.
• Програмирање: Utilize the open-sourced demo program and HEX files provided by WONDOM to get started or to restore factory settings. All terminal functions can be tailored to specific needs using SigmaStudio.

Одржавање

• Одржавајте јединицу чистом тако што ћете је брисати меком, сувом крпом.
• Избегавајте употребу јаких хемикалија или абразивних средстава за чишћење.
• Обезбедите одговарајућу вентилацију око уређаја како бисте спречили прегревање.
• Редовно проверавајте све кабловске спојеве да ли су безбедно причвршћени.

Решавање проблема

Спецификације

Гаранција и подршка

WONDOM products are manufactured by Sure Electronics. For warranty information, technical support, and further assistance, please refer to the official Sure Electronics webсајт или директно контактирајте њихову корисничку службу. Сачувајте рачун као доказ о куповини за потребе гаранције.

Manufacturer: Sure Electronics

For additional resources and community support regarding SigmaStudio programming, online forums and tutorials can be a valuable resource.