Total TG5411611 Gasoline Chainsaw User Manual

Увод

This manual provides essential instructions for the safe operation, maintenance, and troubleshooting of your Total TG5411611 Gasoline Chainsaw. Please read this manual thoroughly before operating the chainsaw to ensure proper use and to prevent injury or damage. Keep this manual in a safe place for future reference.

The Total TG5411611 is a powerful 2-stroke gasoline chainsaw designed for various cutting tasks. It features a 41cc engine with 2 HP, a 40 cm (16-inch) cutting bar, and is capable of cutting materials up to 405 mm in diameter. It has a fuel tank capacity of 260 ml and an oil tank capacity of 210 ml.

Image 1: Total TG5411611 Gasoline Chainsaw. This image displays the overall appearance of the chainsaw, including the engine housing, handle, and cutting bar with chain.

Важна безбедносна упозорења

• Always wear appropriate personal protective equipment (PPE) including a helmet, eye protection, hearing protection, gloves, and safety boots when operating the chainsaw.
• Уверите се да је радно подручје чисто од пролазника, деце и кућних љубимаца.
• Do not operate the chainsaw when fatigued, under the influence of alcohol, drugs, or medication.
• Inspect the chainsaw before each use for loose parts, damage, or wear. Do not operate a damaged chainsaw.
• Handle fuel with extreme care. Refuel in a well-ventilated area with the engine off and cool. Avoid spilling fuel.
• Maintain a firm grip with both hands on the chainsaw handles during operation.
• Будите свесни повратног удара. Избегавајте сечење врхом водилице.
• Never operate the chainsaw indoors or in poorly ventilated areas due to exhaust fumes.

Подешавање и монтажа

1. Распакивање

Carefully remove all components from the packaging. Verify that all parts listed in the packing list are present and undamaged. Retain packaging materials for future storage or transport.

2. Монтажа водилице и ланца

1. Ensure the engine is off and the chain brake is engaged.
2. Remove the chain cover by loosening the two nuts.
3. Place the guide bar onto the studs, ensuring the chain tension pin aligns with the hole in the guide bar.
4. Carefully fit the chain around the clutch drum and into the groove of the guide bar. Ensure the cutting edges of the chain are facing forward in the direction of rotation.
5. Replace the chain cover and hand-tighten the nuts. Do not fully tighten yet.

3. Подешавање затегнутости ланца

1. Using the chain tensioning screw (usually located on the side of the chainsaw), adjust the chain tension.
2. The chain should be snug against the guide bar, but still able to be pulled freely by hand. There should be no slack on the underside of the bar, and the drive links should be seated in the bar groove.
3. Once the tension is correct, fully tighten the two nuts on the chain cover.
4. Re-check chain tension after tightening the nuts.

4. Fuel and Chain Oil Filling

Важно: This chainsaw uses a 2-stroke engine. It requires a mixture of gasoline and 2-stroke engine oil. Refer to the engine oil manufacturer's instructions for the correct mixing ratio (typically 25:1 or 50:1, depending on the oil type). Use unleaded gasoline with an octane rating of 90 or higher.

1. Уверите се да је мотор искључен и хладан.
2. Locate the fuel tank cap (usually marked with a fuel pump icon) and the chain oil tank cap (usually marked with an oil drop icon).
3. Carefully fill the fuel tank with the correct gasoline/oil mixture (capacity: 260 ml).
4. Fill the chain oil tank with high-quality chain lubricant (capacity: 210 ml). This oil lubricates the chain and guide bar during operation.
5. Securely replace both caps. Wipe up any spills immediately.

Упутство за употребу

1. Покретање мотора

1. Place the chainsaw on a firm, flat surface. Ensure the chain brake is engaged.
2. Set the ON/OFF switch to the "ON" position.
3. Pull the choke lever out (for cold start).
4. Притисните пумпу за гориво неколико пута док се гориво не види у повратном водоводу.
5. Чврсто држите моторну тестеру једном руком на предњој ручки и ставите ногу на задњу ручку.
6. Pull the starter cord briskly until the engine fires (usually a few pulls).
7. Once the engine fires, push the choke lever in halfway (if applicable) or fully in.
8. Поново повуците стартни кабл док мотор не почне да ради глатко.
9. Allow the engine to warm up for a few moments before disengaging the chain brake and beginning work.

2. Основне технике сечења

• Увек одржавајте уравнотежен став и чврсто држите моторну тестеру.
• Plan your cuts to avoid kickback and ensure the wood falls in a safe direction.
• Start cutting with the bottom of the guide bar, using the bumper spike as a pivot point.
• Избегавајте сечење врхом вођице, јер то повећава ризик од повратног ударца.
• Do not force the chainsaw through the wood; let the chain do the work.
• Be aware of pinching. Use wedges if necessary to prevent the guide bar from getting stuck.

3. Заустављање мотора

To stop the engine, simply move the ON/OFF switch to the "OFF" position. Engage the chain brake immediately after stopping the engine.

Одржавање

Regular maintenance is crucial for the safe and efficient operation of your chainsaw. Always ensure the engine is off and cool, and the spark plug cap is disconnected before performing any maintenance.

1. Оштрење ланца

• Оштар ланац је неопходан за безбедно и ефикасно сечење. Редовно оштрите ланац или га замените када се иступи.
• Користите круг file одговарајућег пречника за ваш ланац (погледајте спецификације ланца).
• File each cutter with consistent strokes, maintaining the correct angle.
• Проверите и file the depth gauges as needed.

2. Чишћење ваздушног филтера

Clean the air filter frequently, especially when working in dusty conditions. A clogged air filter can reduce engine performance and increase fuel consumption.

1. Скините поклопац филтера за ваздух.
2. Уклоните елемент филтера за ваздух.
3. Clean the filter with warm, soapy water, or compressed air. Allow it to dry completely before reinstallation.

3. Преглед свећица

Inspect the spark plug periodically for wear, carbon buildup, or damage. Clean or replace as necessary to ensure reliable starting and engine performance.

4. Одржавање водилице

• Редовно чистите жлеб водилице да бисте уклонили пиљевину и остатке.
• Check the guide bar for burrs or wear. File down any burrs.
• Повремено окрећите водилицу како бисте осигурали равномерно хабање.

5. Складиштење

When storing the chainsaw for an extended period, drain the fuel tank or run the engine until it runs out of fuel. Clean the chainsaw thoroughly and store it in a dry, secure location away from children.

Решавање проблема

For issues not covered here, please contact an authorized service center.

Спецификације

Гаранција и подршка

For warranty information, technical support, or to locate an authorized service center, please refer to the warranty card included with your product or visit the official Total Tools webсајт. Сачувајте рачун као доказ о куповини за потребе гаранције.

Произвођач: Укупно

Модел: ТГ5411611