Cooler Master NCORE 100 MAX Bronze ITX SFF Tower Case

1. Увод

This manual provides detailed instructions for the installation, operation, and maintenance of your Cooler Master NCORE 100 MAX Bronze ITX SFF Tower Case. Designed for maximum performance in a minimal form factor, this case integrates superior cooling and power solutions. Please read this manual thoroughly before beginning installation to ensure proper setup and safe operation.

Figure 1: Cooler Master NCORE 100 MAX Bronze ITX SFF Tower Case.

2. Безбедносне информације

Always disconnect power before performing any installation or maintenance. Handle components with care to avoid damage. Static electricity can harm electronic components; consider using an anti-static wrist strap. Keep small parts away from children.

3. Садржај пакета

• NCORE 100 MAX Bronze ITX SFF Tower Case
• Custom 120mm AIO Liquid Cooler (Pre-installed)
• 850W SFX Gold ATX3.0 PSU (Pre-installed)
• Custom PCIe 4.0 Riser Cable
• Accessory Box (Screws, zip ties, additional cables)

4. Подешавање и инсталација

The NCORE 100 MAX is designed for easy assembly. Follow these steps for a smooth build process.

4.1. Case Disassembly

The case features a tool-less design for easy access to internal components.

1. Pull off the outer panels.
2. Уклоните горњу плочу.
3. Unlock the corner cable cover's tool-less latches, rotate the cable cover, and then remove it.

Слика 2: Експлодирао view demonstrating the tool-less disassembly of the NCORE 100 MAX.

4.2. Инсталација матичне плоче

Install your Mini-ITX motherboard into the case. The case supports both Intel and AMD motherboards.

1. Place the bracket on the back of the motherboard (after CPU installation, please see motherboard's manual).
2. Mount the four standoffs and tighten each by hand.
3. Place the motherboard into the case by sliding it in, back IO panel first.
4. Tighten the 4 screws to secure the motherboard.
5. Install the 8-pin EPS cable.
6. Install the 24-pin EPS cable.
7. Install front panel connector for Power button.
8. Install USB connectors.
9. Plug in HD audio connector.

Refer to the official installation video for detailed steps:

4.3. CPU Cooler Installation (AIO)

The NCORE 100 MAX comes with a pre-installed custom 120mm AIO liquid cooler for optimal CPU cooling.

1. Install two brackets on the pump.
2. Apply a pea-sized drop of thermal paste to the center of the CPU.
3. Remove the foil and lightly place the cooling block face down on the CPU.
4. Apply the 4 nuts to the standoffs, and gently tighten by hand.
5. Tighten the 4 nuts with a screwdriver, alternating between each after every turn and being careful not to over tighten.
6. Connect the pump's 3-pin header to the motherboard's "AIO pump" header.
7. Connect the radiator fan's 4-pin cable to the "CPU-fan" header.
8. Connect the rear fan's 4-pin cable to the "CHA-FAN" or "Chassis fan" header.

Слика 3: Унутрашњи view of the NCORE 100 MAX showing the pre-installed AIO cooler and PSU.

4.4. Инсталација графичке картице

The NCORE 100 MAX supports various GPU sizes. Ensure proper placement and connection of the PCIe 4.0 riser cable.

1. Install the GPU, ensuring that the PCIe connector is placed properly in its slot.
2. Tighten the GPU screws.
3. Install the 16-pin power connector, ensuring it is properly seated.

For specific GPU lengths and thicknesses, refer to the official installation video:

Figure 4: Custom PCIe 4.0 Riser Cable for graphics card installation.

4.5. SSD Installation

Install your 2.5" SSD drives.

1. Tighten the tool-less SSD mounting pins by hand.
2. Connect the SATA power cable to the PSU.
3. Connect the SATA data cable to the SSD.
4. Fit the pins into the bottom panel rubber rings. (Tip: align the back two pins first).

Refer to the official installation video for detailed steps:

4.6. Менаџмент каблова

The NCORE 100 MAX comes with pre-routed cables for the integrated PSU and AIO, simplifying cable management. Ensure all cables are neatly tucked away to maintain optimal airflow.

Слика 5: Унутрашњи view of the NCORE 100 MAX with pre-routed cables.

4.7. Поновно састављање

1. Install the front cable cover and lock it into place by hand.
2. Install the top cover by hand.
3. Install the external panels by hand.

Refer to the official installation video for detailed steps:

5. Упутство за употребу

Once all components are installed and secured, connect your peripherals and power cable. Press the power button on the front panel to start your system. Ensure all fans are spinning and no unusual noises are present.

6. Одржавање

• Чишћење: Regularly clean dust filters and internal components using compressed air. Ensure the system is powered off and unplugged before cleaning.
• Термална паста: Reapply thermal paste to the CPU every 2-3 years or if CPU temperatures are consistently high.
• Управљање кабловима: Periodically check cable routing to ensure no cables are obstructing airflow or fan blades.

КСНУМКС. Решавање проблема

8. Спецификације

9. Гаранција и подршка

За информације о гаранцији и техничку подршку, посетите званичну веб страницу Cooler Master-а. webсајт или контактирајте њихову корисничку службу. Сачувајте доказ о куповини за потребе гаранције.

Visit the Cooler Master Store