ErGear Dual Monitor Desk Mount EGCM13B Instruction Manual

Увод

Thank you for choosing the ErGear Dual Monitor Desk Mount. This manual provides detailed instructions for the safe and efficient installation, operation, and maintenance of your new monitor mount. Please read this manual thoroughly before installation and keep it for future reference.

Важне информације о безбедности

Please ensure all instructions are read and understood before assembly and use. If you have any questions, please contact customer service. Failure to follow these instructions may result in property damage, serious injury, or death.

• Verify that your monitor's weight and VESA pattern are within the specified limits.
• Do not exceed the maximum load capacity of 26.5 lbs per arm.
• Ensure the mounting surface (desk) is strong enough to support the combined weight of the mount and monitors.
• Use only the provided hardware.
• Држите мале делове даље од деце.

Спецификације

• Модел: EGCM13B
• Компатибилност величине екрана: 13 до 34 инча
• Носивост (по руци): До 26.5 лбс
• ВЕСА компатибилност: 75x75 mm, 100x100 mm
• Arm Span: 33 инча
• Висина стуба: 16.3 инча
• Тип покрета: Tilt, Swivel, Rotation, Articulating
• Максимални угао нагиба: 90 степени
• Материјал: легирани челик
• Боја: Црно
• Тип монтаже: Носач за сто (C-Clamp или ушушка)
• Ц-Цлamp Дебљина стола: 0.39" - 3.15"
• Grommet Mount Desk Thickness: 0.39" - 2.17"
• Пречник отвора за ушну шкољку: 0.47" - 0.79"

Садржај пакета

Please check that all parts are included and undamaged. If any parts are missing or damaged, please contact customer service.

• Главни стуб са столом Clamp/Grommet Base
• Дуал Монитор Армс
• VESA плоче (2x)
• Прибор за монтажу (шрафови, подлошке, алати)
• Клипови за управљање кабловима
• Упутство за употребу

Подешавање и инсталација

1. Провера компатибилности са столом

Before installation, ensure your desk meets the following criteria:

• Материјал: Recommended for wooden tables.
• Доња страна: Preferably free of beams or panels that may interfere with installation.
• Ц-Цлamp дебљина: 0.39" - 3.15"
• Дебљина монтаже ушнице: 0.39" - 2.17" (Hole Diameter: 0.47" - 0.79")

2. Monitor Compatibility Check

Each monitor must meet these conditions:

• Величина екрана: 13 до 34 инча
• Тежина: До 26.5 лбс
• ВЕСА рупе за монтажу: 75x75 mm or 100x100 mm apart on the back of the monitor.

3. Assemble the Pole with Clamp Подршка

Choose either C-Clamp or Grommet installation based on your desk type.

Follow the detailed steps in the provided video and diagrams to securely attach the main pole to your desk using either the C-Clamp or Grommet method. Ensure all screws are tightened appropriately for stability.

4. Assemble the Arm and Pole Wire Clips

Attach the monitor arms to the main pole. Loosen the screw on the pipe clamp before installing the arm, then tighten it securely. Ensure the VESA plate side of the arm faces upwards. Install the cable management clips along the arms and pole.

5. Assemble VESA Plate and Monitor

Attach the VESA plate to the back of your monitor using the appropriate screws and washers. Ensure it is securely fastened.

6. Install the Monitor to the Swivel Arm

Carefully slide the monitor (with the attached VESA plate) onto the swivel arm. Secure it by tightening the locking screw. Adjust the screw with the Allen key to adjust the height of the VESA panel as needed (clockwise to lower, counter-clockwise to raise).

Рад и подешавања

The ErGear Dual Monitor Desk Mount offers versatile adjustments for optimal viewутеха:

• Подешавање висине: Отпустите цлamp on the main pole to slide the arms up or down to your desired height. Re-tighten the clamp сигурно.
• Нагиб: Adjust the monitor's vertical angle by tilting it +/-45 degrees to reduce glare and eye strain.
• Окретни: Rotate the monitor horizontally +/-90 degrees for easy screen sharing or viewинг из различитих углова.
• ротација: Окрените монитор за 360 степени да бисте прелазили између пејзажне и портретне оријентације.
• Испружање/увлачење руке: The articulating arms allow you to extend or retract your monitors closer or further from you. Adjust the tension screws on the arm joints as needed to hold the desired position.

Одржавање

• Периодично проверавајте све завртње и спојеве како бисте били сигурни да су чврсто затегнути и безбедно причвршћени.
• Очистите носач меком крпомamp тканина. Избегавајте абразивна средства за чишћење.
• Do not disassemble the mount unless instructed to do so.

Решавање проблема

• Monitors are not level: Ensure the VESA plates are correctly aligned and tightened. Adjust the small bolts on the tilt head to fine-tune alignment.
• Monitors sag or do not hold position: Tighten the tension screws on the arm joints. Refer to the assembly instructions for specific locations.
• Носач делује нестабилно: Double-check that the C-Clamp or Grommet mount is securely fastened to the desk and all screws are fully tightened. Ensure your desk meets the thickness requirements.

Гаранција и подршка

For warranty information or technical support, please refer to the product packaging or contact ErGear customer service directly. Keep your purchase receipt as proof of purchase.