CENTURY AOKE DC 12V-36V 315MHz 4-Channel Wireless Remote Control Switch User Manual

1. Увод

This manual provides detailed instructions for the installation, operation, and maintenance of the CENTURY AOKE DC 12V-36V 315MHz 4-Channel Wireless Remote Control Switch. This device is designed for various wireless control applications, offering reliable and flexible control over electrical systems.

Молимо вас да пажљиво прочитате ово упутство пре инсталације и употребе како бисте осигурали правилно функционисање и безбедност.

2. Безбедносне информације

• Ensure the power supply is disconnected before any installation or wiring to prevent electric shock.
• Проверите да ли је улазна волtage matches the receiver's specifications (DC 12V-36V).
• Do not exceed the maximum load current of 10A for the receiver.
• Држите уређај даље од воде, влаге и екстремних температура.
• Само квалификовано особље треба да обавља инсталацију и одржавање.
• This device is not intended for life-support systems or other applications where device failure could result in injury or death.

3. Садржај пакета

Пакет укључује следеће ставке:

• 1 x Receiver Unit (Wireless 4 Channels Remote Controller)
• 2 x Transmitter Units (4-Button Remote Controls)

4. Спецификације

Receiver Unit (Model: AK-C211008)

Transmitter Unit (Remote Control)

Слика 1: Receiver Unit Dimensions. The unit measures approximately 95mm in length, 62mm in width, and 28mm in height.

5. Подешавање и ожичење

Before wiring, ensure the power supply is completely disconnected. Refer to the wiring diagrams below for correct connections based on your application.

5.1. Output 12-36V Voltagе Дијаграм ожичења

Слика 2: Output 12-36V Voltage Wiring. Connect your DC 12-36V power input to the receiver's input terminals. Connect your loads to the ON (Normally Open) and COM (Common) terminals for each channel. The NC (Normally Closed) terminal can also be used depending on the desired circuit behavior.

5.2. Output Switch Signal Wiring Diagram

Слика 3: Output Switch Signal Wiring. This diagram shows how to use the receiver to provide a dry contact switch signal. Connect the DC12-36V input power. The output terminals (ON, COM, NC) act as a switch, controlling an external circuit without directly powering the load from the receiver's output.

5.3. DC 12-36V Motor Wiring Diagram

Слика 4: DC 12-36V Motor Wiring. This diagram illustrates how to connect two DC motors for directional control. Input DC 12-36V power is supplied. Each motor (M) is connected across two channels, allowing for forward and reverse operation or independent control.

6. Радни режими

The receiver supports six different operating modes, which can be changed using the learning button on the receiver board. The modes determine how the receiver responds to button presses on the remote control.

6.1. Momentary Mode (Jog Mode)

Press the learning button once. When a remote button is pressed, the relay turns ON. When the remote button is released, the relay turns OFF.

6.2. Toggle Mode (Self-Locking Mode)

Press the learning button twice. When a remote button is pressed, the relay turns ON. Press the same button again, and the relay turns OFF.

6.3. Latch Mode (Interlock Mode)

Press the learning button three times. When a remote button is pressed, the corresponding relay turns ON, and all other relays turn OFF. This mode ensures only one relay is active at a time.

6.4. 2-Channel Momentary + 2-Channel Latch Mode

Press the learning button four times. Channels 1 and 2 operate in Momentary mode. Channels 3 and 4 operate in Latch mode.

6.5. 2-Channel Momentary + 2-Channel Toggle Mode

Press the learning button five times. Channels 1 and 2 operate in Momentary mode. Channels 3 and 4 operate in Toggle mode.

6.6. 2-Channel Toggle + 2-Channel Latch Mode

Press the learning button six times. Channels 1 and 2 operate in Toggle mode. Channels 3 and 4 operate in Latch mode.

7. Learning and Clearing Remote Codes

The receiver needs to "learn" the codes from your remote control transmitters to function. You can also clear all learned codes if needed.

7.1. Learning a Remote Control

1. Press the learning button on the receiver board the number of times corresponding to your desired operating mode (e.g., once for Momentary, twice for Toggle, etc.). The indicator light on the receiver will flash and then turn OFF.
2. Release the learning button.
3. Press any button on your remote control transmitter.
4. The indicator light on the receiver will flash three times, indicating that the learning process was successful.

Напомена: You must press the learning button the correct number of times for the desired mode before pressing the remote button.

7.2. Clearing All Remote Codes

1. Press and hold the learning button on the receiver board for approximately 8 seconds.
2. The indicator light will flash several times and then turn OFF.
3. Release the learning button.
4. Press any button on your remote control. The relay should not respond. This confirms that all codes have been successfully cleared.

8. Пријаве

This wireless remote control switch is versatile and can be used in a wide range of applications, including but not limited to:

• Anti-theft alarm control systems
• Electric doors and gates
• Опрема за дизање
• Контрола ЛЕД осветљења
• Лифтови
• Electric curtains and roller shutters
• Отварачи гаражних врата
• Системи контроле приступа
• Индустријски контролни системи
• Automotive applications (e.g., car alarms, remote start)
• Household switches

Слика 5: Application Scenarios. The remote control switch can be integrated into various systems for wireless control, such as garage doors, electric vehicles, cranes, and household appliances.

КСНУМКС. Решавање проблема

10. Одржавање

• Чишћење: Use a soft, dry cloth to clean the receiver and remote control. Do not use liquid cleaners or solvents.
• Замена батерије: Replace the remote control battery when the operating range decreases or the indicator light on the remote becomes dim.
• Услови животне средине: Ensure the receiver is installed in a dry environment, protected from direct sunlight, rain, and extreme temperatures.
• Провере везе: Периодично проверавајте све спојеве ожичења како бисте били сигурни да су безбедни и да немају корозије.

11. Гаранција и подршка

This product comes with a standard manufacturer's warranty. For specific warranty details, please refer to the product packaging or contact your retailer. If you encounter any issues or require technical assistance, please contact CENTURY AOKE customer support through the retailer's platform or their official webсајту.

Please provide your product model number (AK-C211008) and a detailed description of the issue when seeking support.