Valkyrie V360 Lite AIO CPU Liquid Cooler

1. Увод

This manual provides detailed instructions for the installation, operation, and maintenance of your Valkyrie V360 Lite AIO CPU Liquid Cooler. Please read this manual thoroughly before installation to ensure proper setup and optimal performance. This cooler is designed to provide efficient thermal management for high-performance CPUs, featuring a 360mm radiator, RGB LED fans, and compatibility with various AMD and Intel sockets.

Image 1.1: The Valkyrie V360 Lite AIO CPU Liquid Cooler with its three RGB fans and pump unit.

2. Садржај пакета

Verify that all components listed below are present in your package. If any items are missing or damaged, please contact Valkyrie customer support.

• Valkyrie V360 Lite AIO Cooler (360mm Radiator with Integrated Pump)
• 120mm FDB RGB Fans (x3)
• Mounting Brackets for Intel (LGA 1851)
• Носачи за монтажу за AMD (AM5/AM4)
• Backplates for Intel and AMD
• Монтажни вијци и одстојници
• Thermal Paste (pre-applied or tube)
• Фан Сцревс
• RGB Controller and Cables
• Упутство за употребу

Image 2.1: Included mounting hardware for various CPU sockets.

Image 2.2: Close-up of Intel and AMD mounting brackets, along with the tightening tool.

3. Подешавање и инсталација

Before beginning installation, ensure your system is powered off and unplugged. Refer to your motherboard manual for specific CPU socket information.

3.1 Опште мере предострожности

• Пажљиво рукујте компонентама како бисте избегли оштећења.
• Avoid touching the CPU contact surface of the cold plate.
• Ensure proper cable management to prevent interference with fans or other components.

3.2 Уградња радијатора и вентилатора

1. Determine the optimal mounting location for the 360mm radiator in your PC case (top, front, or side).
2. Attach the three 120mm fans to the radiator using the provided fan screws. Ensure the fan airflow direction is appropriate for your case's cooling strategy (intake or exhaust).
3. Mount the assembled radiator and fans into your chosen location in the PC case using the longer radiator screws.

3.3 CPU Block Installation (Intel LGA 1851)

1. Install the Intel backplate onto the rear of your motherboard, aligning the holes with the CPU socket.
2. Secure the Intel standoffs through the motherboard from the front, screwing them into the backplate.
3. Apply thermal paste to the center of your CPU if it is not pre-applied on the cold plate.
4. Align the CPU block with the standoffs and gently place it onto the CPU.
5. Secure the CPU block using the Intel mounting bracket and thumb screws, tightening them in a diagonal pattern until snug. Do not overtighten.

3.4 CPU Block Installation (AMD AM5/AM4)

1. Remove the existing plastic retention clips from the motherboard's AM5/AM4 socket, but retain the stock backplate.
2. Screw the AMD standoffs into the stock backplate's mounting holes.
3. Apply thermal paste to the center of your CPU if it is not pre-applied on the cold plate.
4. Align the CPU block with the standoffs and gently place it onto the CPU.
5. Secure the CPU block using the AMD mounting bracket and thumb screws, tightening them in a diagonal pattern until snug. Do not overtighten.

3.5 Кабловске везе

• Connect the pump's 3-pin or 4-pin power cable to the CPU_FAN or AIO_PUMP header on your motherboard. Consult your motherboard manual for the recommended header.
• Connect each fan's 4-pin PWM cable to available fan headers on your motherboard or to a fan hub.
• Connect the RGB cables from the fans and pump to the included RGB controller, then connect the controller to an available 5V ARGB header on your motherboard (if applicable) or to a SATA power connector for standalone control.

Image 3.1: The Valkyrie V360 Lite AIO cooler installed in a typical PC build.

4. Упутство за употребу

After successful installation, power on your system and verify proper operation.

4.1 Прво покретање

• Upon first boot, check that the pump is running (you may hear a faint hum or feel vibrations in the tubes) and that all fans are spinning.
• Monitor CPU temperatures using system monitoring software (e.g., HWMonitor, CPU-Z) to ensure the cooler is functioning effectively.

4.2 RGB контрола осветљења

• If connected to a motherboard's ARGB header, use your motherboard's RGB software (e.g., ASUS Aura Sync, MSI Mystic Light, Gigabyte RGB Fusion) to customize lighting effects.
• If using the standalone RGB controller, refer to its specific instructions for cycling through lighting modes.

Image 4.1: The pump head featuring customizable RGB lighting.

5. Одржавање

Regular maintenance helps ensure the longevity and performance of your AIO cooler.

• Уклањање прашине: Периодично чистите прашину са ребара хладњака и лопатица вентилатора помоћу компримованог ваздуха. Уверите се да се вентилатори не окрећу током чишћења.
• Визуелни преглед: Occasionally inspect the tubing and connections for any signs of leaks or damage.
• Нема делова које корисник може сервисирати: The AIO unit is a sealed system. Do not attempt to open the pump or radiator, as this will void the warranty and may cause damage.

КСНУМКС. Решавање проблема

Ако наиђете на проблеме, погледајте следеће уобичајене кораке за решавање проблема.

• Високе температуре процесора:
  • Ensure the pump is powered and running.
  • Verify the CPU block is securely mounted and making good contact with the CPU.
  • Check that thermal paste was applied correctly.
  • Confirm fans are spinning and oriented correctly for airflow.
• Fans Not Spinning/RGB Not Lighting:
  • Check all power and RGB cable connections to the motherboard or controller.
  • Ensure fan headers on the motherboard are enabled in BIOS/UEFI.
  • Verify RGB software settings.
• Необична бука:
  • Identify if the noise is from the pump or fans.
  • For pump noise, ensure the pump is not running dry (though unlikely in a sealed AIO).
  • For fan noise, check for obstructions or loose fan screws.

If issues persist, contact Valkyrie customer support for further assistance.

7. Спецификације

Key technical specifications for the Valkyrie V360 Lite AIO CPU Liquid Cooler.

Image 7.1: Radiator dimensions, indicating a thickness of 27mm.

Image 7.2: The copper cold plate on the underside of the pump unit.

8. Гаранција и подршка

Valkyrie products are manufactured to high standards and undergo rigorous quality control. For warranty information, technical support, or to report any issues, please refer to the official Valkyrie webсајт или контактирајте њихову службу за кориснике. Сачувајте доказ о куповини за потребе гаранције.