AirheadStorm Replacement Parts Kit for BPMIO B12 / B12 NEW Robot Vacuum

1. Увод

This manual provides essential information for the installation, maintenance, and replacement of the AirheadStorm 11-Pack Replacement Parts Kit designed for BPMIO B12 and BPMIO B12 NEW Robot Vacuums. Regular replacement of these components ensures optimal performance and extends the lifespan of your robot vacuum cleaner.

2. Производ је готовview

The AirheadStorm replacement kit includes a comprehensive set of parts to maintain your BPMIO B12 / B12 NEW robot vacuum's cleaning efficiency. The kit contains:

• 1 Main Brush: Designed to effectively pick up dirt, debris, and hair from various floor surfaces.
• 4 Side Brushes: Engineered to reach and clean corners and edges, sweeping away dust and dirt from hard-to-reach areas.
• 3 Filters: Captures small particles and reduces dust circulation, improving air quality.
• 3 Mop Pads: Efficiently pick up dirt and dust, leaving floors clean during mopping cycles.

Слика 1: Готовоview of the AirheadStorm 11-Pack Replacement Parts Kit, showing the main brush, side brushes, filters, and mop pads.

3. Упутства за инсталацију

Before installing any replacement parts, ensure your robot vacuum is powered off and disconnected from its charging base. Refer to your robot vacuum's original manual for specific compartment access instructions.

3.1. Уградња главне четке

1. Locate the main brush compartment, usually on the underside of the robot vacuum.
2. Open the main brush cover or guard, typically by pressing release tabs.
3. Remove the old main brush. Clean any debris from the compartment.
4. Insert the new main brush, ensuring the ends align with the slots in the vacuum.
5. Close the main brush cover until it clicks securely into place.

3.2. Уградња бочне четке

1. Окрените роботски усисивач наопачке.
2. Locate the side brushes. Depending on your model, they may be secured by a screw or simply snap into place.
3. If applicable, use a screwdriver to remove the screw holding the old side brush. Remove the old brush.
4. Align the new side brush with the post and press it down firmly or secure it with the screw.

3.3. Уградња филтера

1. Open the dustbin compartment and remove the dustbin from the robot vacuum.
2. Locate the filter housing within the dustbin.
3. Remove the old filter. Dispose of it properly.
4. Insert the new filter into the housing, ensuring it sits flush.
5. Close the dustbin and reinsert it into the robot vacuum.

3.4. Mop Pad Installation

1. Locate the mop pad attachment area on your robot vacuum, typically on the underside or a dedicated water tank.
2. Remove the used mop pad.
3. Attach the new mop pad, ensuring it is securely fastened (e.g., via Velcro or clips).

Слика 2: Крупни план view of the replacement filters and mop pads.

4. Распоред одржавања и замене

To maintain optimal cleaning performance, it is recommended to replace parts according to the following schedule. Actual replacement frequency may vary based on usage and environment.

• Главна четка: Replace every 6-12 months. Inspect monthly for tangled hair or debris.
• Бочне четке: Replace every 3-6 months. Inspect monthly for wear or bending.
• Филтери: Replace every 2-3 months. Clean weekly by tapping out dust.
• Крпе за брисање: Replace every 1-3 months, or as needed based on wear. Wash after each use.

Слика 3: Крупни план view of the replacement main brush and side brushes.

КСНУМКС. Решавање проблема

If you encounter issues after replacing parts, consider the following:

• Делови који не одговарају: Ensure you have the correct replacement kit for your specific BPMIO B12 or B12 NEW model. Double-check alignment during installation.
• Смањене перформансе чишћења: Verify all parts are installed correctly and securely. Check for any remaining debris in the vacuum's compartments. Ensure filters are not clogged.
• Необични звуци: Re-check the main brush and side brushes for proper installation. Ensure no hair or debris is caught in the brush mechanisms.

6. Спецификације

7. Гаранција и подршка

Specific warranty information for this replacement parts kit is not provided in the product details. For any support inquiries or questions regarding the AirheadStorm replacement parts, please refer to the seller's contact information on the platform where the purchase was made.