AWithZ UK1 Mini Portable Spot Welder Instruction Manual

1. Увод

The AWithZ UK1 Mini Portable Spot Welder is a versatile and compact tool designed for precise spot welding applications, particularly for battery pack assembly and repair. Featuring a 9000W output, it offers stable welding performance while protecting battery cells. Its intuitive knob control and dual operating modes (automatic and pedal) make it suitable for both beginners and experienced users.

This manual provides essential information on the safe and effective use of your AWithZ UK1 spot welder. Please read it thoroughly before operation.

Figure 1: AWithZ UK1 Mini Portable Spot Welder with key components.

2. Безбедносне информације

• Always wear appropriate personal protective equipment, including safety glasses, during operation to protect against sparks.
• Уверите се да је радна површина добро проветрена и да нема запаљивих материјала.
• This spot welder is није погодан for welding copper, gold, silver, or jewelry.
• When welding pure nickel, a flux may be required to achieve optimal results.
• Do not attempt to weld materials thicker than the specified limits to avoid damaging the device or producing weak welds.
• Држите уређај даље од воде и високе влажности.
• Не растављајте нити модификујте уређај. Сво сервисирање препустите квалификованом особљу.

3. Садржај пакета

Проверите да ли су све ставке присутне у пакету:

• 1 x AWithZ UK1 Spot Welding Unit
• 2 x WP110 Spot Welding Pens
• 1 к ножна педала
• 1 x Nickel-Plated Strip (approx. 2m)
• 1 x USB-C Charging Cable (approx. 0.5m)
• 1 x Sandpaper
• 1 к Упутство за употребу
• 1 pair of spare Soldering Pins

Figure 2: All included components in the AWithZ UK1 package.

4. Производ је готовview

The AWithZ UK1 is designed for portability and ease of use. It features a compact body with an intuitive control interface.

4.1 Физичке карактеристике

• Димензије: Приближно 150 мм (дужина) x 100.5 мм (ширина) x 48 мм (висина).
• Тежина: Approximately 370g (main unit).
• батерија: Built-in high-quality Lithium-polymer battery.

4.2 Interface and Controls

• Adjustment Knob/Button: Used for powering on/off, toggling options, and adjusting parameters. Rotate clockwise to increase, counter-clockwise to decrease. Short press to confirm selections.
• Екран: LED display showing current mode, gear (power level), trigger settings, and continuous weld count.
• Trigger Interface: Port for connecting the foot pedal.
• Порт за пуњење типа Ц: За пуњење унутрашње батерије.
• Spot Welding Pen Installation Interface: Ports for connecting the welding pens.

Слика 3: Детаљно view of the AWithZ UK1 unit with dimensions and interface labels.

5. Подешавање

5.1 Почетно пуњење

Before first use, fully charge the spot welder. Connect the provided USB-C charging cable to the Type-C charging port on the device and to a suitable USB power adapter (not included).

• The display will indicate charging status. A full circle on the display indicates 100% charge.
• It is recommended to charge the device regularly, even during periods of inactivity, to maintain battery health.

5.2 Connecting Welding Pens

Insert the two spot welding pens into the designated installation interfaces on the front of the unit. Ensure they are securely connected.

5.3 Connecting Foot Pedal (Optional)

If using the foot pedal for manual welding, plug its connector into the Trigger Interface port on the unit.

6. Упутство за употребу

6.1 Укључивање/искључивање

To power on or off the device, дуги притисак дугме за подешавање.

6.2 Подешавање параметара

The AWithZ UK1 offers precise control over welding parameters via its single knob interface. The display shows four main adjustable parameters: Mode, Gear, Trigger, and Cont Welds.

1. Окрените дугме to cycle through the available options (Mode, Gear, Trigger, Cont Welds).
2. Short press the knob to select the flashing option and enter adjustment mode for that parameter.
3. Окрените дугме to adjust the parameter value (clockwise to increase, counter-clockwise to decrease).
4. Short press the knob again to confirm the new setting and exit adjustment mode for that parameter.

Figure 4: Knob operation for parameter adjustment.

Детаљи параметра:

• Режим: Selects between Automatic (A) and Pedal (M) welding modes.
• Опрема: Adjusts the welding power level from 1 to 100. Higher numbers indicate more power.
• Окидач: (Only for Automatic Mode) Sets the delay time (0.5-5 seconds) before a weld is triggered after the pens contact the material.
• Cont Welds: Sets the number of continuous welding pulses (1 or 2) for a single trigger.

6.3 Процес заваривања

The AWithZ UK1 is suitable for welding nickel-plated steel (0.1-0.35mm), pure nickel (0.1mm), and steel (0.1-0.3mm) for battery pack assembly and repair. It is commonly used for 18650 battery welding.

1. Припремите материјал: Ensure the nickel strip and battery terminals are clean and free of oxidation. Use the included sandpaper if necessary.
2. Поставите траку: Place the nickel strip firmly onto the battery terminal where the weld is desired.
3. Позиционирање оловки за заваривање: Hold the welding pens perpendicular to the nickel strip, with the tips making firm contact with the strip, directly above the battery terminal. Ensure the tips are close to each other but not touching.
4. Започните заваривање:
   • Аутоматски режим: The weld will trigger automatically after the set delay once both pen tips make contact.
   • Режим педала: Press the foot pedal to trigger the weld. This offers more precise control over the timing.
5. Прегледајте завар: After welding, gently test the strength of the weld. Adjust the 'Gear' (power level) as needed for stronger or weaker welds.

Figure 5: Illustration of Auto Mode and Foot Pedal Mode for welding.

Figure 6: Welding power levels and material compatibility.

7. Одржавање

7.1 Electrode Tip Maintenance

Over time, the welding tips may oxidize or become worn, affecting weld quality. Use the provided sandpaper to gently polish the tips to remove any oxide layer. Replace the soldering pins if they become excessively worn or damaged.

Figure 7: Detachable welding pen and replaceable welding needle.

7.2 Складиштење

Store the device in a cool, dry place when not in use. Detach the welding pens for easier storage and portability.

КСНУМКС. Решавање проблема

• Weak or Inconsistent Welds:
  • Ensure welding tips are clean and polished.
  • Increase the 'Gear' (power level) setting.
  • Verify the material thickness is within the specified range.
  • Ensure firm contact between welding pens, nickel strip, and battery terminal.
• Уређај се не укључује:
  • Проверите ниво напуњености батерије и напуните ако је потребно.
  • Ensure the power button (knob) is long-pressed correctly.
• прегревање: The device features intelligent thermal protection and auto-shutoff after 8 minutes of inactivity to prevent overheating. Allow the device to cool down if it becomes excessively warm.

9. Спецификације

10. Гаранција и подршка

AWithZ is committed to providing reliable products and excellent customer service. If you have any questions, concerns, or require technical assistance regarding your UK1 Mini Portable Spot Welder, please contact AWithZ customer support through the retailer where you purchased the product.