Rittal 1058000
Rittal AX Compact Enclosure
Упутство за употребу модела 1058000
Важне информације о безбедности
ОПРЕЗ: This enclosure contains electrical components. Always follow proper safety procedures when installing, using, or maintaining. Do not attempt to service while energized. Wear appropriate personal protective equipment (PPE).
Read this manual thoroughly before installation and operation. Keep this manual for future reference. Failure to follow these instructions may result in equipment damage, personal injury, or death.
Производ је завршенview
The Rittal AX Compact Enclosure Model 1058000 is designed for housing electrical and electronic components, providing protection against environmental factors. It features a robust metal construction and meets NEMA 12 specifications, ensuring protection against dust, dirt, and dripping non-corrosive liquids.

Слика: Фронт view of the Rittal AX Compact Enclosure, showcasing its high-gloss finish and robust design.
Сетуп
1. Распакивање
- Carefully remove the enclosure from its packaging.
- Inspect the enclosure for any signs of damage during transit. Report any damage to the carrier immediately.
- Verify all components listed in the packing slip are present.
2. Монтажа
The enclosure can be wall-mounted or stand-mounted. Ensure the mounting surface is capable of supporting the total weight of the enclosure and its contents.

Слика: Позади view of the Rittal AX Compact Enclosure, highlighting the designated mounting points for secure installation.
- Одредите жељену локацију за монтажу.
- Mark the drilling points using the enclosure's mounting holes as a template.
- Drill appropriate holes for your chosen fasteners.
- Securely attach the enclosure to the mounting surface using suitable hardware (not included).
- Ensure the enclosure is level and plumb.
3. Internal Component Installation
Before installing components, ensure the enclosure is de-energized and all safety precautions are observed.

Image: Rittal AX Compact Enclosure with the door open, revealing the internal mounting plate and space for component installation.
- Open the enclosure door using the provided key.
- Install internal mounting plates, rails, or other accessories as required for your components.
- Mount electrical and electronic components securely within the enclosure.
- Route all wiring neatly and ensure proper strain relief.
Оперативни
1. Accessing the Enclosure
- To open the door, insert the key into the lock and turn.
- To close the door, swing it shut and turn the key to lock it. Ensure the door is fully sealed to maintain the enclosure's protective rating.
2. Увод за каблове
Utilize the designated cable entry points, typically located at the bottom or sides of the enclosure. Ensure proper cable glands or conduit fittings are used to maintain the NEMA 12 rating.
- Select appropriate cable glands for the cable diameter.
- Install cable glands into the pre-punched or drilled openings.
- Pass cables through the glands and tighten them to ensure a secure, watertight seal.
Одржавање
1. Чишћење
- Regularly clean the exterior of the enclosure with a soft, damp тканина.
- Avoid abrasive cleaners or solvents that could damage the high-gloss finish.
- For internal cleaning, ensure the power is disconnected. Use a dry, lint-free cloth or a vacuum cleaner to remove dust and debris.
2. Инспекција
- Periodically inspect the door gasket for signs of wear or damage. Replace if necessary to maintain the NEMA 12 rating.
- Проверите да ли је сав монтажни хардвер заптивеност.
- Inspect cable glands and conduit fittings for secure connections and seals.
- Verify that all internal components are securely mounted and wiring is intact.
Решавање проблема
| Проблем | Могући узрок | Решење |
|---|---|---|
| Врата се не затварају правилно | Obstruction in the door frame; damaged hinge; misaligned latch. | Check for obstructions. Inspect hinges and latches for damage or misalignment. Adjust or replace as needed. |
| Улазак воде или прашине | Damaged or improperly seated door gasket; loose cable glands; unsealed openings. | Inspect and replace door gasket if damaged. Tighten all cable glands and ensure all unused openings are properly sealed. |
| Enclosure feels unstable after mounting | Лабави монтажни елементи; неадекватна површина за монтажу. | Tighten all mounting bolts. Verify the mounting surface is structurally sound and capable of supporting the load. |
Спецификације
| Феатуре | Детаљ |
|---|---|
| Број модела | 1058000 |
| Бранд | Риттал |
| Материјал | Метал |
| Финисх Типе | Висок сјај |
| Спецификација Мет | НЕМА КСНУМКС |
| УПЦ | 639889914728 |
| ASIN | B0G1CQVR34 |
Гаранција и подршка
For specific warranty information regarding the Rittal AX Compact Enclosure Model 1058000, please refer to the official Rittal website or contact Rittal customer service directly. Warranty terms and conditions may vary by region and purchase date.
For technical support, spare parts, or further assistance, please visit the Rittal Store on Amazon or the official Rittal corporate webсајту.
Ask a question about this manual
Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.