Universal Wireless Remote Control System

1. Производ је готовview

This Universal Wireless Remote Control System, featuring a 433Mhz RF Relay Receiver and a Long Range Transmitter, is designed for controlling various devices such as garage doors, gates, motors, and lighting. It offers multiple operating modes to suit diverse application scenarios.

Апликације

2. Спецификације

Receiver (Model: KR1204-4-V02)

Ремоте Цонтрол

3. Компоненте производа

Рецеивер Боард

• Релеји: Four independent relays for controlling different circuits.
• Напајање: Connects to DC 6V-30V power supply.
• Learning Button: Used for programming operating modes and pairing remotes.
• ЛЕД индикатор: Пружа визуелну повратну информацију током програмирања и рада.
• Антена: Receives RF signals from the transmitter. Stretch for optimal range.
• NC COM NO Terminals: Output terminals for connecting controlled devices. NC (Normally Closed), COM (Common), NO (Normally Open).

Даљински управљач предајник

• Slide Closure: Protects buttons from accidental presses.
• Silicone Buttons (A, B, C, D): Used to send commands to the receiver.
• ЛЕД индикатор: Lights up when a button is pressed.
• Антена: Transmits RF signals.
• батерија: Powered by one 23A12V battery (included).

4. Инсталација

Упозорења о инсталацији

1. Always connect wires with the power supply turned OFF.
2. Connect wires correctly according to the circuit diagram; do not reverse polarity.
3. When fixing wires in the terminal, tighten screws firmly. Ensure each wire is separated and does not touch others to prevent short circuits.
4. The receiver and transmitter are usually paired at the factory. If not, you will need to reprogram them.
5. Perform a reset before changing the operating mode.
6. After a reset, all previously paired remote controls will no longer function and will need to be reprogrammed.
7. Replace the remote transmitter battery promptly when its voltagе је низак.
8. Slightly stretch the antenna on the receiver for better signal reception and extended range.
9. After the receiver is powered on and in use, avoid touching metal parts on the circuit board by hand to prevent electric shock.
10. Place the receiver in a stable, dry location where it is not easily touched or disturbed.
11. Тип излаза је пасивни излаз / контакти без потенцијала.

Дијаграми ожичења

Connect the wires correctly based on the device you intend to control. Different devices require different wiring configurations.

5. Operating Modes and Programming

The receiver supports four operating modes. You can program the receiver to your desired mode. Note: The remote control kit is typically pre-programmed at the factory. If not, or if you wish to change modes, follow the instructions below.

Оперативни режими

1. Тренутни режим:
   - Press and hold button 'A' on the remote: Relay '1' will turn ON.
   - Release button 'A': Relay '1' will turn OFF.
2. Пребаци режим:
   - Press button 'A' once: Relay '1' will turn ON.
   - Press button 'A' again: Relay '1' will turn OFF.
3. Латцхед Моде: (Note: In this mode, the receiver always keeps one relay ON. It cannot turn all relays OFF simultaneously.)
   - Press button 'A': Relay '1' will turn ON.
   - Press button 'B': Relay '2' will turn ON, and simultaneously Relay '1' will turn OFF.
4. Миксни режим: This mode allows for combinations of the above modes across different relays.
   - Прample combinations:
   a. 2 Relays in Momentary mode; 2 Relays in Toggle mode.
   b. 2 Relays in Momentary mode; 2 Relays in Latched mode.
   c. 2 Relays in Toggle mode; 2 Relays in Latched mode.

Упутства за програмирање

To program a mode, you must first clear any existing data. After clearing, proceed with the programming steps for your desired mode.

1. Clean Data (Reset):
   - Press the learning button (on the receiver) 8 times.
   - The indicator LED on the receiver will flash several times and then turn OFF. This indicates a successful reset. All previously paired remotes will be cleared.
2. Program Momentary Mode:
   - Press the learning button (on the receiver) 1 time.
   - The indicator LED on the receiver will light up.
   - Press button 'A' on the remote transmitter.
   - The indicator LED on the receiver will flash several times and then turn OFF. Programming is successful.
3. Program Toggle Mode:
   - Press the learning button (on the receiver) 2 times.
   - The indicator LED on the receiver will light up.
   - Press button 'A' on the remote transmitter.
   - The indicator LED on the receiver will flash several times and then turn OFF. Programming is successful.
4. Program Latched Mode:
   - Press the learning button (on the receiver) 3 times.
   - The indicator LED on the receiver will light up.
   - Press button 'A' on the remote transmitter.
   - The indicator LED on the receiver will flash several times and then turn OFF. Programming is successful.
5. Program Mix Mode:
   - Press the learning button (on the receiver) 4, 5, or 6 times (depending on the desired mix combination, refer to the specific mix mode requirements).
   - The indicator LED on the receiver will light up.
   - Press button 'A' on the remote transmitter.
   - The indicator LED on the receiver will flash several times and then turn OFF. Programming is successful.

6. Одржавање и решавање проблема

Одржавање

• Regularly check the remote control battery and replace it when the indicator LED dims or fails to light up.
• Уверите се да су сви спојеви ожичења безбедни и без корозије.
• Keep the receiver in a clean, dry environment, away from excessive heat, moisture, and direct sunlight.
• Periodically check the receiver's antenna for any damage and ensure it is stretched for optimal performance.

Решавање проблема

If the receiver and transmitter are not operating normally, try the following steps:

1. Проверите батерије: Verify if the remote control battery is depleted. The indicator LED on the remote transmitter should light up brightly when a button is pressed. If it doesn't, replace the battery.
2. Проверите ожичење: Ensure your receiver is wired correctly according to the provided diagrams. Incorrect wiring is a common cause of malfunction.
3. Reprogram: If the above steps don't resolve the issue, try reprogramming the receiver and transmitter. This often resolves pairing or mode-related problems. Remember to clear data first if changing modes.
4. сметње: Ensure there are no strong RF interference sources nearby that could be disrupting the signal.

7. Савети корисника

• Independent Motor Control: For applications requiring independent control of multiple motors (e.g., two-motor schemes), ensure you program the relays in Momentary or Toggle mode, assigning each motor to a separate relay and remote button.
• Simultaneous Button Presses: In Momentary or Toggle modes, pressing multiple buttons simultaneously will activate their respective relays. In Latched mode, pressing a new button will deactivate the previously active relay before activating the new one.
• Оптимизација опсега: For maximum remote range, ensure the receiver's antenna is fully extended and unobstructed. Environmental factors like walls and other electronic devices can reduce the effective range.
• Mode Changes: Always perform a 'Clean Data' (reset) operation before attempting to program the receiver into a different operating mode. This prevents conflicts from previous settings.

8. Гаранција и подршка

This device is compatible with Directive 2014/53 EU Rules, ensuring compliance with essential requirements for radio equipment.

For further assistance or if problems persist after troubleshooting, please contact our support team:

• Емаил: диесеелецтрониц@163.цом
• ВхатсАпп: +86 13502278583 / +86 18138805271
• Адреса: Room 03, 12th Floor, Building T19, East Coast Garden, Fangzhilonghuwan, No. 27, Sanhuan South Road, Huicheng District, Huizhou City, Guangdong Province, China 516001

Additional documentation, including a detailed user manual in PDF format, can be found at the following links:

• Упутство за употребу (ПДФ)
• Product Info 1
• Product Info 2