1. Производ је готовview
The ESP32-WROOM-32 Development Board integrates an ESP32 module with either a 1.14-inch or 1.9-inch ST7789 TFT LCD display. This board provides all the functionalities of a traditional ESP32 module, including various peripheral ports, high-performance development tools, and high-definition data display capabilities. It is designed for a wide range of IoT projects, offering both Wi-Fi and Bluetooth Low Energy (BLE) connectivity.
Figure 1: ESP32-WROOM-32 Development Board with integrated LCD.
Кључне карактеристике:
- Integrated ESP32 module with 1.14-inch or 1.9-inch LCD screen.
- Supports multiple programming modes.
- 2.4GHz Wi-Fi and Bluetooth (BT+BLE) functionality.
- Low power consumption and high performance.
- Multiple interfaces: UART, SPI, SDIO, I2C, PWM, I2S, IR, ADC, DAC.
- Suitable for IoT projects, WiFi solutions, Mini cameras, Mesh networking, smart homes, and mobile IoT applications.
Видео производа прекоview
Видео 1: Кратак прегледview of the ESP32-WROOM-32 Development Board.
2. Спецификације
Општи параметри:
| Параметар | Валуе |
|---|---|
| Интерфејс | ТИПЕ-Ц |
| Воркинг Волtage | УСБ 5В |
| Дривер Цхип | ЦХ340 |
| Величина ЛЦД екрана | 1.14 inches / 1.9 inches (variant dependent) |
| СПИ Фласх | Подразумевано 32Мбит |
| Serial Port Rate | 115200бпс |
| Фреквенцијски опсег | 2412-2484МХз |
| Блуетоотх протокол | Bluetooth 4.2 BR/EDR and BLE standards |
| ВиФи протокол | 802.11 б/г/н |
| Antenna Form | Onboard PCB antenna, gain 2dBi |
| Подржани интерфејси | UART, SPI, SDIO, I2C, PWM, I2S, IR, ADC, DAC |
| Димензије | 63.70 мм к 31.5 мм |
| Радна температура | -20~70℃ |
LCD Screen Parameters (1.14-inch exampле):
| Параметар | Валуе |
|---|---|
| Материјал | ISP LCD |
| Резолуција | 135(H)RGBx240(V) |
| Дривер Цхип | СТ7789В |
| Комуникациони интерфејс | 4 LINE SPI |
| Боја екрана | Пуна боја |
| Дисплаи Ареа | 14.864 (В) к 24.912 (В) |
| Панел Сизе | 17.6(В)к31.0(В)к1.6(Д) |
| Начин повезивања | Plug-in 8Pin (0.5mm pitch FPC) or Welding 13Pin (0.7mm pitch FPC) |
| Viewинг Дирецтион | СвеView |
| Воркинг Волtage | 3.3В |
| Воркинг Цуррент | 20мА |
| Тип позадинског осветљења | 1ЛЕД |
Figure 2: Front and back dimensions of the 1.14-inch ESP32 Development Board. Front: 59.5mm/2.34in length, 27.4mm/1.08in width, 31.5mm/1.24in height. Positioning hole diameter: 2.00mm/0.08in.
Figure 3: Front and back dimensions of the 1.9-inch ESP32 Development Board. Front: 63.70mm/2.51in length, 27.4mm/1.08in width, 31.5mm/1.24in height. Positioning hole diameter: 2.00mm/0.08in.
Слика 4: Детаљно view of the back of the ESP32 Development Board, showing power light, GPIO2 pin indicator, battery charging interface, and Type-C interface. EN button enables reset, BOOT button for firmware download mode, USB for power/communication.
3. Подешавање и почетна конфигурација
3.1 Повезивање хардвера
- Connect the ESP32 Development Board to your computer using a Type-C USB cable.
- Verify that the power indicator light on the board illuminates.
- Open your computer's Device Manager (or equivalent for your OS) and check for COM port recognition. Look for "USB-SERIAL CH340 (COMxxx)".
Figure 5: Screenshot of Device Manager showing the recognized COM port for the CH340 chip.
3.2 Software Environment Setup (Ard-IDE Exampле)
- Open Ard-IDE software (version 1.8.5 or later).
- Дођите до
File->Preferences. - In the "Additional Boards Manager URLs" field, copy and paste the following URL:
https://dl.espressif.com/dl/package_esp32_index.json. Click "OK". - Иди на
Tools->Board->Boards Manager.... - In the Boards Manager window, search for "ESP32" and install the Espressif Systems ESP32 development environment.
Figure 6: Ard-IDE Preferences window, highlighting where to add the ESP32 Boards Manager URL.
Figure 7: Ard-IDE Boards Manager, showing the installation of the ESP32 development environment.
3.3 Board Parameter Configuration
- Restart the Ard-IDE software.
- Иди на
Tools->Boardand select "ESP32 Wrover Module". - Испод
Tools->Port, select the COM port identified in step 3.1 (e.g., COM266). - Configure other board parameters as follows:
- Core Debug Level: "None"
- Erase All Flash Before Sketch Upload: "Disabled"
- Flash Frequency: "80MHz"
- Flash Mode: "QIO"
- Partition Scheme: "Default 4MB with spiffs (1.2MB APP/1.5MB SPIFFS)"
- Upload Speed: "921600"
Figure 8: Ard-IDE showing the configured board parameters for the ESP32 Wrover Module.
4. Упутство за употребу
4.1 Uploading Firmware (LCD Display Exampле)
- Open the "WIFI AP LCD" routine in Ard-IDE.
- Click the "Upload" button to compile and upload the routine to the development board.
- If the upload fails, press and hold the
BOOTbutton on the board, then plug in the USB cable (while still holdingBOOT), release theBOOTbutton, and try uploading the program again. - Upon successful upload, the server will start, and the IP address
192.168.4.1биће приказано на ЛЦД екрану. - Connect to the ESP32's Wi-Fi network from your computer or mobile device, then access the displayed IP address in a web browser to configure the screen to display monochrome or pictures.
Figure 9: Ard-IDE displaying the successful upload of the "WIFI AP LCD" routine.
4.2 Pinout Diagram
Refer to the following diagram for the pin assignments of the ESP32-WROOM-32 Development Board:
Figure 10: Detailed pinout diagram for the ESP32-WROOM-32 Development Board, showing GPIOs, power pins, and special function pins.
5. Одржавање и њега
- Keep the development board in a dry, dust-free environment.
- Avoid exposing the board to extreme temperatures or humidity.
- Handle the board by its edges to prevent damage to components or static discharge.
- Use a soft, dry cloth for cleaning. Do not use liquids or solvents.
- Ensure proper power supply (USB 5V) to prevent damage.
КСНУМКС. Решавање проблема
| Проблем | Могући узрок | Решење |
|---|---|---|
| Board not recognized by computer / "I can't get it to work." | Missing or incorrect CH340 driver. Faulty USB cable or port. | Install the correct CH340 driver for your operating system. Try a different USB cable or port. Ensure the board is properly connected. |
| Отпремање фирмвера не успева. | Board not in firmware download mode. Incorrect COM port or board settings in IDE. | Притисните и држите BOOT button, then plug in the USB cable, release BOOT, and try uploading again. Verify COM port and board settings in Ard-IDE (e.g., "ESP32 Wrover Module", correct COM port, upload speed). |
| LCD display is blank or shows incorrect output. | Incorrect code uploaded. Display initialization issues. | Ensure the correct LCD routine is uploaded. Double-check wiring if using external display (not applicable for integrated). Verify display parameters in code match the board's LCD. |
| Проблеми са Wi-Fi везом. | Incorrect Wi-Fi credentials in code. Weak signal. | Verify Wi-Fi SSID and password in your sketch. Ensure the board is within range of your Wi-Fi router. |
7. Савети корисника
- Always ensure the correct drivers (e.g., CH340) are installed on your computer before connecting the board to avoid recognition issues.
- When encountering upload problems, remember the
BOOTbutton sequence: holdBOOT, plug in USB, then releaseBOOTbefore attempting to upload. This often resolves common firmware flashing issues. - For detailed programming examples and community support, refer to the official Espressif ESP32 documentation and online forums.
8. Гаранција и подршка
For technical support, troubleshooting assistance, or warranty inquiries, please contact the seller or manufacturer directly. Refer to the official product page or included documentation for specific contact information.
Свеобухватно корисничко упутство у PDF формату доступно је за преузимање: Преузмите кориснички приручник (PDF).
