1. Увод
The SC07 Universal 2-Channel Garage Gate Receiver Module is designed to provide versatile control for various automation systems. This module is compatible with a wide range of remote controls operating on frequencies between 300MHz and 900MHz, supporting both fixed and rolling code technologies. It is ideal for integration into gate automation systems, burglar alarm systems, electric doors, windows, and lifting equipment. Its compact design, low power consumption, and ease of connection make it a reliable solution for enhancing your existing control systems.
2. Спецификације
| Феатуре | Опис |
|---|---|
| Број модела | СЦ07 |
| Оператинг Волtage | АЦ/ДЦ 9V-30V |
| Канали | 2 |
| Фреквенцијски опсег | 300MHz - 900MHz (including 300MHz, 310MHz, 315MHz, 318MHz, 390MHz, 433MHz, 433.4MHz, 433.92MHz, 868MHz, 868.3MHz, 868.8MHz) |
| Code Compatibility | Rolling Code (HCS301, HCS300, HCS200, HCS201, HCS100, HCS101), Fixed Code (2262, 2260, 2264, 5326, M1E, M5E), Learning Code (1527, 2240, 6P20B, 6P20D) |
| Бежична комуникација | RF |
| Удаљеност | 30-50 meters (Open Area) |
| Капацитет меморије | До 400 кодова |
| Осетљивост | -105дБ |
| Радни режим | Моментари |
| Димензије | 5.5 цм к 4.5 цм к 1.0 цм |
| Материјал | Metal and PVC |
| Цертифицатион | ЦЕ, ФЦЦ |
3. Садржај пакета
- 1 x SC07 Receiver Module
- 1 x Small Antenna
- 1 к енглески приручник
4. Подешавање
4.1 Power Input Selector (PIS)
The receiver operates on AC/DC 9V-30V. It is crucial to correctly set the Power Input Selector (PIS) based on your power supply voltage:
- Ако је улазна волtage is greater than 24V, shorten pins 2 & 3.
- Ако је улазна волtage is less than 24V, shorten pins 1 & 2.
4.2 Дијаграм ожичења
Connect the receiver module to your gate automation system or other devices using the terminal block. Refer to the diagram below for connection points:
Слика: Фронт view of the white receiver module, showing PWR (Power Input), OUT1 (Output 1), OUT2 (Output 2), GND (Ground), and ANT (Antenna) terminals. Also visible are L1/L2 LEDs, S1/S2 learn buttons, and the 8-position DIP switch.
- ПВР: Connect your AC/DC 9V-30V power supply here.
- OUT1 / CH1: Output for Channel 1 (relay output).
- OUT2 / CH2: Output for Channel 2 (relay output).
- ГНД: Уземљење.
- МРАВ: Connect the provided small antenna here for optimal signal reception.
5. Упутство за употребу
5.1 Brand Selection (DIP Switches)
The receiver features 8 DIP switches to select the correct brand and frequency for the remote control you wish to program. Each remote brand may require a specific DIP switch combination. Refer to the diagram below for common brand settings:
Слика: Детаљна view of the 8-position DIP switch with various settings for different remote control brands and frequencies (e.g., Marantec, Hormann, Nice, etc.). Switches are labeled 1 through 8.
To select a brand, move the corresponding DIP switches UP or DOWN as indicated for your remote control's brand and frequency. For example, for a 433.92MHz Marantec remote control, move Dip-switch 7 UP.
5.2 Programming a New Remote Control
- Select Brand: Ensure the correct brand and frequency are selected using the 8 DIP switches (refer to Section 5.1).
- Уђите у режим учења: Press the learn button (S1 for Channel 1, S2 for Channel 2) on the receiver module. The corresponding LED (L1 or L2) will turn on, indicating it's in learning mode.
- Transmit Remote Signal: Press the desired button on your remote control. The LED on the receiver will flash 4 times, confirming successful programming.
- Repeat for Additional Buttons: If your remote has multiple buttons you wish to program, repeat step 2 and 3 for each button.
- Други канал: The programming procedure for the second channel (using S2 and L2) is identical.
5.3 Ерasing All Data from Memory
To clear all programmed remote controls from the receiver's memory:
- Press and hold either learn button (S1 or S2). The LED will begin to flash.
- Continue holding the button until the LED turns off. All saved data in the memory will be permanently erased and cannot be recovered.
6. Савети корисника
- Напајање: Always double-check your power supply voltage (AC/DC 9V-30V) and ensure the PIS (Power Input Selector) is correctly configured before powering on the module.
- Положај антене: For optimal reception range, ensure the small antenna is connected and positioned away from metal obstructions.
- тестирање: After programming a remote, always test the range and functionality of the receiver before fully integrating it into your system.
- сметње: The receiver is designed not to interfere with other remotes and receivers, but ensure your remote is transmitting on the correct frequency for the selected brand.
КСНУМКС. Решавање проблема
- Remote Not Programming:
- Verify that the DIP switches are set correctly for your remote control's brand and frequency.
- Ensure your remote control has a working battery and is transmitting a signal.
- Try erasing all data from the receiver's memory (Section 5.3) and then re-program the remote.
- Short Operating Range:
- Check that the antenna is securely connected and not obstructed by metal objects.
- Ensure there are no major sources of radio frequency interference nearby.
- The stated range of 30-50 meters is for open areas; obstructions will reduce this.
- Нема напајања за пријемник:
- Check all wiring connections to the PWR and GND terminals.
- Verify that your power supply is providing the correct voltagе (9В-30В АЦ/ДЦ).
- Ensure the PIS (Power Input Selector) is correctly set for your voltage.
- Receiver Not Responding to Programmed Remote:
- Confirm that the remote was successfully programmed (LED flashes 4 times).
- Check if the remote's frequency matches the DIP switch settings.
- Ensure the remote is not too far from the receiver.
8. Одржавање
- Чишћење: Одржавајте модул чистим и без прашине и прљавштине. Користите меку, суву крпу за чишћење.
- Окружење: Avoid exposing the module to extreme temperatures, high humidity, or direct water contact.
- Инспекција ожичења: Периодично проверавајте све спојеве ожичења да ли су лабави или оштећени.
9. Гаранција и подршка
За информације о гаранцији, техничку подршку или било која питања која нису обухваћена овим упутством, обратите се продавцу или директно произвођачу. Сачувајте рачун као доказ о куповини.
