AOLON W3002 Microcomputer Temperature Controller
Техничке спецификације
| Спецификација | Детаљи |
|---|---|
| Назив производа | Microcomputer Temperature Controller (XH-W3002) |
| Меасуринг Ранге | -50°C to 110°C (-50°C to 100°C model variation) |
| Контролни опсег | -50°C to 110°C (-50°C to 100°C model variation) |
| Прецизност мерења температуре | ±0.2°Ц |
| Прецизност контроле температуре | ±0.1°Ц |
| Меасуремент Инпут | NTC10K L=1m waterproof probe |
| Input Power Options | 12V / 24V / 220V AC/DC |
| Опције излазне снаге | 120W (12V) / 240W (24V) / 1500W (220V) |
| Оутпут Типе | Директан излаз |
| Излазни капацитет | Мак 10А |
| Installation Hole Distance | 73mm (Hole size: 4mm) |
| Димензије | 60 мм × 45 мм × 31 мм |
Брзо подешавање и коришћење
- Connect the temperature sensor: use the supplied NTC10K waterproof probe (L=1m).
- Provide power using one supported option: 12V/24V/220V AC/DC.
- Set start temperature (P0): press the Подешавање button to enter the menu (default to P0), press Подешавање again, then use Up/Доле to set the desired start temperature.
- Set stop temperature (P1): in the menu, use Up/Доле to select P1, press Подешавање again, then adjust with Up/Доле.
- (Optional) Calibrate temperature (P2): select P2, press Подешавање to enter calibration, then set the offset value using Up/Доле.
- (Optional) Set delayed start (P3): select P3 and set the delay time (minutes) using Up/Доле (recommended 3–6 minutes for compressor-based refrigeration; otherwise leave at 0).
Wiring Diagrams & Safety Information
12V / 24V Connection Way
Напомена: 12V/24V power supplies must use a stable DC power source.
220V Connection Way
Упозорење: This model is designed with direct output power. Exercise extreme caution when connecting the electricity. Ensure the load is connected to the output terminal port before powering up to prevent potential output short circuit ignition or sparks.
Settings Parameter Menu
| Код | Опис | Опсег подешавања | Фацтори Дефаулт |
|---|---|---|---|
| P0 | Почетна температура | -50 до 110°Ц | Ночьу 00°Ц |
| P1 | Зауставите температуру | -50 до 110°Ц | Ночьу 00°Ц |
| P2 | Корекција температуре | -10 до 10°Ц | Ночьу 0°Ц |
| P3 | Delay to start | 0 до 10 минута | КСНУМКС минута |
Parameter Configurations & Functions
P0: Start-up Temperature Setting
Притисните тастер Подешавање button to enter the internal menu. The display will default to P0. Притисните тастер Подешавање button once more, then use the Up и Доле buttons to set your desired start temperature.
Притисните тастер Подешавање button to enter the internal menu. When
P0 is displayed, use the Up or Доле дугмад за избор P1. Притисните тастер Подешавање button again, and adjust the target stop temperature using the Up и Доле дугмад.Притисните тастер Подешавање button to enter the internal menu, then switch to
P2 користећи се Up or Доле дугмад. Притисните тастер Подешавање button again to calibrate. Use the Up и Доле buttons to enter the offset value.Calibration Formula: Detected Temperature + Calibration Temperature = Actual Temperature
- If the detected temperature is 0.5°C higher than the actual temperature: Set P2 to -0.5°Ц
- If the detected temperature is 1.0°C lower than the actual temperature: Set P2 to Ночьу 1.0°Ц
P3: Delayed Start Setting
Притисните тастер Подешавање button to enter the internal menu and switch to P3 користећи се Up or Доле дугмад. Притисните тастер Подешавање button again and set the delay time in minutes using the Up or Доле дугмад.
Напомена: This function is typically used for compressor-based refrigeration systems (like refrigerators or freezers) to protect the motor. A delay of 3 to 6 minutes is recommended. If you are not controlling a compressor, leave this set to 0.
Оперативни режими
Режим грејањаправило:Start-up Temperature (P0) < Stop Temperature (P1) The system automatically determines it is in heating mode when P0 is configured lower than P1.
Exampле Сценарио:
Control a water heater to turn off when the temperature reaches 50°C and restart heating when the temperature drops back down to 40°C.
- Verify that the heating rule is met: Start-up (40°C) is less than Stop (50°C).
- Притисните тастер Подешавање button, enter the menu, select
P0, and adjust the value to Ночьу 40°Ц. - Притисните тастер Подешавање button, enter the menu, select
P1, and adjust the value to Ночьу 50°Ц.
Режим хлађењаправило: Start-up Temperature (pø) > Stop Temperature (Pl). The system automatically determines it is in cooling mode when P0 is configured higher than P1.
Exampле Сценарио:
Control a cabinet radiator to turn on when temperatures reach 30°C and stop cooling once the temperature drops to 26°C.
- Verify that the cooling rule is met: Start-up (30°C) is greater than Stop (26°C).
- Притисните тастер Подешавање button, enter the menu, select
P0, and adjust the value to Ночьу 30°Ц. - Притисните тастер Подешавање button, enter the menu, select
P1, and adjust the value to Ночьу 26°Ц.
Решавање проблема
Common Fault: Incorrect Settings
If you set your temperature values upside down (e.g., configuring heating parameters with P0 > P1), the output indicator light will remain off and the connected load will not work. Check the temperature values in your P0 и P1 settings if the system is unresponsive.
With the controller powered on, press and hold both the Up и Доле buttons simultaneously for approximately 3 seconds. Once the digital tube displays
888, The controller will automatically return to real-time temperature detection, indicating a successful factory reset.- Display “LLL”: Indicates a temperature sensor probe failure. Please inspect, repair, or replace the waterproof probe.
- Display “HHH”: Indicates that the ambient temperature has exceeded the controller’s detection range. Relocate the unit to an appropriate environment.
Документи / Ресурси
 | W3002 Microcomputer Temperature Controller |
Референце
- Упутство за употребуmanual.tools