1. Производ је готовview
The M MARANTEC M3-2314 Digital 384 4-Channel 315MHz Remote Transmitter is designed to operate compatible Marantec garage door openers. This remote provides convenient access to your garage door system with its multi-channel capability.
It is engineered for reliable performance and ease of use, serving as a replacement or additional remote for your Marantec garage door opener.
2. Компатибилност
This remote transmitter is compatible with the following Marantec garage door opener systems:
- All Marantec 315 MHz garage door openers with a serial number starting with 31 or higher, or manufactured from 2004 to current.
- Garage door opener models: M-4500, M-4700, Q-7500, Q-7700, Q-7900, M-Line, Q-Line.
- Older remote models: ML-1312V, ML-1314, ML-2314, ML-3313.
Важно: To verify compatibility, locate the serial number on your main garage door opener power head. If your serial number starts with 30 or less, contact Marantec support for assistance in matching the correct replacement remote.
3. Садржај пакета
Your M3-2314 remote transmitter package includes:
- Marantec M3-2314 Remote Transmitter
- Visor Clip or Keyring attachment
- Battery (pre-installed or included separately)
- Кабл за програмирање
- Programming Instructions (detailed steps for your specific opener model)
4. Подешавање и програмирање
To program your M3-2314 remote transmitter to your garage door opener, follow these general steps. Always refer to the specific programming instructions included with your remote and your garage door opener's user manual for detailed, model-specific procedures.
4.1. Remote Overview
Слика 1: Предња страна view of the M3-2314 remote, displaying the four programmable buttons and LED indicator.
4.2. Programming Steps (General Guide)
- Prepare the Opener: Locate the programming button or terminals on your Marantec garage door opener's power head. This is typically labeled 'Program', 'P', or similar.
- Connect Programming Cable: If your opener model requires it, connect the provided programming cable between the remote and the designated port on your garage door opener.
- Активирајте режим програмирања: Press and hold the programming button on your garage door opener until the indicator light (often red or green) illuminates or flashes, indicating it is in programming mode. Release the button.
- Program Remote Button: Within 30 seconds of activating programming mode on the opener, press the desired button on your M3-2314 remote transmitter that you wish to program. The opener's indicator light may change or flash to confirm successful programming.
- Пробни рад: After programming, disconnect the cable (if used) and wait a few seconds. Press the programmed button on your remote to test if the garage door operates correctly.
- Program Additional Buttons: Repeat the process for any other buttons on the remote you wish to program for additional garage doors or functions.
If you encounter difficulties, consult the detailed programming instructions that came with your remote or your garage door opener's manual. Marantec's official website may also provide support resources.
5. Operating the Remote
Once programmed, operating your M3-2314 remote is straightforward:
- Отварање/затварање врата: Press the programmed button once to open or close your garage door.
- Stop Door: Press the programmed button again while the door is in motion to stop it.
- Више врата: If you have programmed multiple buttons for different garage doors, press the corresponding button for the desired door.
- ЛЕД индикатор: The small LED light on the remote will illuminate when a button is pressed, indicating that a signal is being transmitted.
6. Одржавање
6.1. Замена батерије
The remote transmitter is powered by a coin cell battery, typically a CR2032. When the remote's range decreases significantly or the LED indicator light becomes dim or fails to illuminate, it's time to replace the battery.
Слика 2: Позади view of the M3-2314 remote, showing the battery compartment.
- Пронађите одељак за батерију: Turn the remote over to its back. The battery compartment is usually a small cover that can be slid or unclipped.
- Отворени одељак: Use a small coin or screwdriver to gently pry open the battery compartment cover.
- Уклоните стару батерију: Carefully remove the old CR2032 battery. Note its orientation.
- Уметните нову батерију: Insert a new CR2032 battery with the positive (+) side facing up (or as indicated inside the compartment).
- Затвори одељак: Вратите поклопац одељка за батерију, водећи рачуна да се сигурно уклопи на своје место.
Старе батерије одлажите одговорно у складу са локалним прописима.
КСНУМКС. Решавање проблема
| Проблем | Могући узрок | Решење |
|---|---|---|
| Remote does not operate the garage door. |
|
|
| Даљински управљач ради повремено. |
|
|
| LED on remote does not light up. |
|
|
8. Спецификације
| Феатуре | Детаљ |
|---|---|
| Број модела | М3-2314 |
| Фреквенција | 315 МХз |
| Канали | 4-канал |
| Тежина артикла | 1.44 унце (приближно 40.8 грама) |
| Димензије пакета | 3.23 x 2.72 x 0.79 инча (приближно 8.2 x 6.9 x 2.0 цм) |
| Тип батерије | CR2032 Coin Cell (estimated) |
9. Гаранција и подршка
For warranty information, technical support, or further assistance with your M MARANTEC M3-2314 remote transmitter, please refer to the documentation included with your product or visit the official M MARANTEC webсајту. Контакт информације за корисничку подршку су обично доступне на сајту произвођача webсајту.
Always ensure you are using genuine Marantec parts and accessories for optimal performance and safety.
