Keithley 2303-PJ Power Supply Instruction Manual
Model: 2303-PJ
1. Производ је готовview
The Keithley 2303-PJ is a specialized power supply designed for testing portable, battery-operated devices. It offers advanced capabilities to simulate a battery's performance across a wide range of conditions, including output resistance and voltage response. This instrument is crucial for accurately testing device charge control circuitry and overall battery simulation.
Кључне карактеристике укључују:
- Ultra-fast response to transient load currents
- Variable output resistance
- 100nA DC current sensitivity
Figure 1: Front panel of the Keithley 2303-PJ Power Supply. The display shows voltage and current readings (e.g., 3.60V, 1.08A). Controls include a navigation pad, 'DISPLAY', 'MENU', 'OPERATE', 'ENTER', 'SET' buttons, and a 'POWER' button with indicator lights.
2. Подешавање
- Распакивање и преглед: Carefully remove the instrument from its packaging. Inspect for any signs of damage during transit. Report any damage to the shipping carrier and Keithley immediately.
- Прикључак за напајање: Connect the supplied AC power cord to the instrument's rear panel power inlet and then to a grounded AC power outlet. Ensure the power source matches the instrument's voltagе захтеве.
- Почетно укључивање: Притисните тастер ПОВЕР button located on the front panel. The display should illuminate, indicating the unit is operational.
- Connecting to Device Under Test (DUT): Use appropriate test leads to connect the output terminals of the 2303-PJ to the device you intend to test. Observe correct polarity.
- вентилација: Ensure adequate ventilation around the instrument. Do not block the ventilation grilles on the sides or rear of the unit.
3. Упутство за употребу
3.1 Контроле на предњој плочи
- Приказ: Приказује излазну јачину звукаtage, current, and other operational parameters.
- Навигациона дугмад (горе, доле, лево, десно): Used to navigate through menus and adjust parameter values.
- Дугме ЕНТЕР: Confirms selections or entered values.
- СЕТ дугме: Enters parameter setting mode.
- Дугме МЕНУ: Accesses the main menu for configuration and advanced settings.
- OPERATE Button: Toggles the output on or off.
- Дугме ПРИКАЗ: Cycles through different display modes or views.
3.2 Основни рад
- Сеттинг Волtagе и струја:
- Притисните тастер СЕТ дугме.
- Use the navigation buttons to select the voltage or current parameter you wish to adjust.
- Use the navigation buttons (typically Up/Down) to change the value.
- Притисните ЕНТЕР да потврдите подешавање.
- Омогућавање излаза:
- Once parameters are set, press the ОПЕРАТЕ button to enable the power output. The output indicator should illuminate.
- To disable the output, press ОПЕРАТЕ опет.
- Праћење очитавања:
The display continuously shows the actual output voltage and current. Use the ДИСПЛАИ button to cycle through different measurement viewако је доступно.
4. Одржавање
- Чишћење: Keep the instrument clean by wiping the exterior with a soft, damp cloth. Do not use abrasive cleaners or solvents. Ensure the unit is powered off and disconnected from the AC supply before cleaning.
- вентилација: Periodically check that the ventilation grilles are free from dust and debris to ensure proper airflow and prevent overheating.
- Складиштење: When not in use for extended periods, store the instrument in a clean, dry environment within its specified operating temperature and humidity ranges.
- калибрација: For optimal performance and accuracy, periodic calibration by qualified personnel is recommended. Refer to the Keithley service manual or contact Keithley support for calibration procedures and intervals.
КСНУМКС. Решавање проблема
| Проблем | Могући узрок | Решење |
|---|---|---|
| Инструмент се не укључује. | No AC power; faulty power cord; internal fuse blown. | Check AC power connection and outlet. Try a different power cord. If fuse is suspected, contact qualified service personnel. |
| Но оутпут волtagе/цуррент. | Output disabled; incorrect settings; overload protection active; faulty connections. | Притисните ОПЕРАТЕ to enable output. Verify voltage/current settings. Check for short circuits or overloads on the DUT. Ensure test leads are securely connected. |
| Нестабилна или нетачна очитавања. | Poor connections; external interference; instrument needs calibration. | Check all connections for looseness or corrosion. Ensure the instrument is away from strong electromagnetic fields. Consider professional calibration. |
| Прегревање. | Blocked ventilation; excessive ambient temperature; continuous operation at maximum load. | Ensure ventilation grilles are clear. Operate in a cooler environment. Reduce load or allow for cool-down periods. |
For issues not listed here or if troubleshooting steps do not resolve the problem, please contact Keithley technical support.
6. Спецификације
| Параметар | Валуе |
|---|---|
| Произвођач | Keithley |
| Парт Нумбер | 2303-PJ |
| Број модела ставке | 2303-PJ |
| Тежина артикла | 5.44 кг |
| Димензије пакета | 48.26 к 33.02 к 22.86 цм |
| Ставка Количина паковања | 1 |
| Батерије су потребне? | бр |
| Датум првог доступног | 4. новембар 2016 |
7. Гаранција и подршка
Warranty information for the Keithley 2303-PJ Power Supply is typically provided with the product at the time of purchase or can be found on the official Keithley webсајт. Молимо вас да сачувате доказ о куповини за потребе гаранције.
For technical support, service, or calibration inquiries, please contact Keithley customer service directly. Refer to the contact information provided in your product documentation or on the official Keithley webсајт (www.tek.com/keithley).
