1. Производ је готовview
The Ozito Air Spray Gun (Model: 4472350) is a versatile tool designed for efficient application of various coatings. Its suction-feed design and adjustable controls make it suitable for a wide range of painting tasks, from general-purpose spraying to applying specific finishes and sealants. This manual provides essential information for safe operation, setup, maintenance, and troubleshooting.
Figure 1: Ozito Air Spray Gun with attached 1000 ml paint pot.
2. Безбедносне информације
Увек се придржавајте основних мера безбедности како бисте смањили ризик од пожара, струјног удара и повреда приликом коришћења овог производа.
- Прочитајте упутство: Thoroughly read and understand all instructions before operating the spray gun.
- Лична заштитна опрема (ЛЗО): Always wear appropriate eye protection (safety glasses/goggles), respiratory protection (respirator mask), and protective gloves.
- вентилација: Use the spray gun in a well-ventilated area to avoid inhalation of fumes and to prevent the buildup of flammable vapors.
- Запаљиви материјали: Do not spray flammable or combustible materials near open flames, pilot lights, or other ignition sources.
- електрична безбедност: Ensure your air compressor and any extension cords are properly grounded and rated for the power requirements.
- Држите децу подаље: Do not allow children or untrained persons to operate the spray gun.
- Сигурне везе: Ensure all air hose connections are secure before operation.
3. Компоненте и делови
The Ozito Air Spray Gun comes with the following main components:
- Suction Spray Gun Body
- 1.5 mm Nozzle (pre-installed or included)
- 1000 ml Paint Pot (Suction Cup)
- Fluid Adjustment Dial
- Fan Adjustment Dials
- Конектор за улаз ваздуха
Слика 2: Страна view of the Ozito Air Spray Gun, showing the handle and air inlet.
4. Подешавање
- Raspakujte: Пажљиво извадите све компоненте из паковања. Проверите да ли има оштећења.
- Connect Air Compressor: Attach a suitable air hose (not included) from your air compressor to the air inlet connector on the spray gun. Ensure the compressor can provide a minimum flow rate of 85 liters per minute.
- Припремите материјал: Prepare your paint, topcoat, or sealant according to the manufacturer's instructions. Ensure it is properly thinned for spraying consistency.
- Fill Paint Pot: Unscrew the paint pot from the spray gun body. Fill the pot with your prepared material, ensuring not to overfill. Reattach the paint pot securely to the spray gun.
- Почетна подешавања: Before spraying, make initial adjustments to the fluid and fan pattern dials. Start with a moderate setting.
5. Упутство за употребу
- Power On Compressor: Turn on your air compressor and allow it to build up sufficient pressure.
- Test Spray Pattern: Before spraying your actual workpiece, test the spray pattern on a piece of scrap material. Adjust the fluid adjustment dial to control the amount of material sprayed and the fan adjustment dials to change the spray pattern (e.g., from a round to a flat pattern).
- Техника прскања: Hold the spray gun perpendicular to the surface, maintaining a consistent distance (typically 6-10 inches). Use smooth, even strokes, overlapping each pass by about 50%. Release the trigger at the end of each stroke.
- Допуна: If the paint pot runs low, turn off the air supply, unscrew the pot, refill, and reattach before resuming.
6. Одржавање
Правилно чишћење и одржавање су кључни за дуготрајност и перформансе вашег пиштоља за прскање.
- Непосредно чишћење: Clean the spray gun immediately after each use. Do not allow material to dry inside the gun.
- Растављање: Disassemble the paint pot, nozzle, and air cap.
- Компоненте за чишћење: Clean all components thoroughly with an appropriate cleaning solution (e.g., paint thinner for oil-based paints, water for water-based paints). Use a cleaning brush to remove any residue from the nozzle and internal passages.
- Поновно састављање: Reassemble the spray gun once all parts are clean and dry.
- Складиштење: Store the spray gun in a clean, dry place, away from extreme temperatures and direct sunlight.
КСНУМКС. Решавање проблема
| Проблем | Могући узрок | Решење |
|---|---|---|
| Без прскања или слабо прскање | Clogged nozzle or air cap; insufficient air pressure; material too thick. | Clean nozzle and air cap; check compressor pressure; thin material. |
| Неравномерно прскање | Dirty air cap; damaged nozzle; incorrect fan adjustment. | Clean air cap; replace nozzle if damaged; adjust fan dials. |
| Material spitting | Material too thick; air leak; low material in pot. | Thin material; check connections for leaks; refill paint pot. |
8. Спецификације
- Назив модела: ASG-SFEU; EX; UK
- Број модела ставке: 4472350
- Бренд: Озито
- Величина млазнице: 1.5 мм
- Paint Pot Capacity: 1000 мл
- Minimum Air Compressor Flow Rate: 85 литара у минути
- Боја: Греи
- Укључене компоненте: 1 suction spray gun
- Димензије пакета: 28.5 к 19 к 11 цм
- Тежина артикла: 790 грама
- Произвођач: Еинхелл
9. Гаранција и подршка
For information regarding warranty coverage, spare parts availability, or technical support, please refer to the official Ozito website or contact Ozito customer service directly. Keep your purchase receipt as proof of purchase for any warranty claims.
Онлине ресурси: Посетите ввв.озито.цом.ау (or your regional Ozito website) for product registration, FAQs, and support contact details.
