Упутство за употребу Everbilt потопне алуминијумске пумпе од 1/2 КС са причвршћеним прекидачем

Увод

This manual provides essential information for the safe and efficient operation, installation, and maintenance of your Everbilt 1/2 HP Submersible Aluminum Sump Pump. Please read all instructions carefully before use to ensure proper function and to prevent injury or damage.

Безбедносне информације

УПОЗОРЕЊЕ: Always disconnect power before servicing or performing any maintenance on the pump.

ОПАСНОСТ: Ризик од струјног удара. Ова пумпа се испоручује са проводником за уземљење и прикључним утикачем за уземљење. Да бисте смањили ризик од струјног удара, будите сигурни да је прикључен само на правилно уземљену утичницу.

• Не користите пумпу ако је кабл за напајање или утикач оштећен.
• Уверите се да је пумпа постављена на стабилну, равну површину.
• Do not pump flammable or corrosive liquids.
• Држите децу и кућне љубимце даље од пумпе која ради.
• Носите одговарајућу личну заштитну опрему (ЛЗО) приликом руковања пумпом.
• This pump is designed for clear water only.

Производ је завршенview

The Everbilt 1/2 HP Submersible Sump Pump is designed for efficient water removal from sump basins. It features an aluminum motor housing for effective cooling and a tethered float switch for automatic operation.

Слика 1: Everbilt 1/2 HP Submersible Aluminum Sump Pump. This image shows the black pump unit with its tethered float switch, power cord, and 1-1/2 inch FNPT discharge port. The Everbilt logo is visible on the side of the pump body.

Кључне карактеристике:

• Aluminum motor housing for efficient motor cooling.
• Continuous duty, efficient 115-Volt PSC motor for lower carbon footprint; higher efficiency using less energy to operate.
• 8.25 ft. cord length.
• Submersible for quiet operation.
• 1-1/2 in. FNPT discharge.
• Semi-open thermoplastic impeller passes 3/8 in. solids.
• Заштита од топлотног преоптерећења.

Подешавање и инсталација

1. Картер Бasin Припрема: Ensure your sump basin has a minimum diameter of 18 inches to accommodate the tethered float switch. Clean the basin of any debris or obstructions.
2. Пласман: Place the pump on a solid, level surface at the bottom of the sump basin. Ensure the pump is stable and will not tip over during operation.
3. Discharge Pipe Connection: Connect a 1-1/2 inch FNPT (Female National Pipe Thread) discharge pipe to the pump's outlet. It is recommended to use a check valve in the discharge line to prevent water from flowing back into the sump basin when the pump turns off.
4. Подешавање пловног прекидача: The tethered float switch controls the pump's on/off cycles. Adjust the tether length to set the desired "on" and "off" water levels. Ensure the float can move freely without obstruction within the sump basin. The switch-on height is approximately 11.81 inches and switch-off height is approximately 3.94 inches, but can be adjusted by tether length.
5. Прикључак за напајање: Plug the pump's 8.25 ft. power cord into a properly grounded 115-Volt AC outlet. Ensure the outlet is protected by a Ground Fault Circuit Interrupter (GFCI) for added safety.
6. Пробни рад: Fill the sump basin with water to activate the float switch and ensure the pump turns on and discharges water correctly. Allow the water level to drop to verify the pump turns off automatically.

Упутство за употребу

The Everbilt 1/2 HP Submersible Sump Pump operates automatically via its tethered float switch. Once properly installed and connected to power, the pump will activate when the water level rises to the "on" point and deactivate when the water level drops to the "off" point.

• Аутоматски рад: The pump is designed for continuous duty and will cycle on and off as needed based on the water level in the sump basin.
• Ручно управљање (ако је применљиво): While primarily automatic, some installations may allow for manual operation by lifting the float switch. Refer to your specific setup for manual control options.
• Надгледање: Periodically check the sump basin and pump operation, especially during heavy rainfall, to ensure it is functioning correctly.

Одржавање

Regular maintenance ensures the longevity and reliable operation of your sump pump.

1. Искључите напајање: Увек искључите пумпу из извора напајања пре него што извршите било какво одржавање.
2. Чисти картер Бasin: Periodically remove any debris, dirt, or sediment from the sump basin that could interfere with pump operation or float switch movement.
3. Проверите импелер: Check the pump's impeller for any clogs or damage. The semi-open thermoplastic impeller is designed to pass 3/8 inch solids, but larger debris can cause issues.
4. Проверите пловни прекидач: Ensure the tethered float switch moves freely and is not obstructed by wires, pipes, or debris.
5. Прегледајте кабл за напајање: Examine the power cord for any signs of wear, cuts, or damage. Replace if necessary.
6. Зимовање (ако је применљиво): If the pump is in an area subject to freezing temperatures and will not be used, remove it from the basin, clean it, and store it in a dry, warm place.

Решавање проблема

If problems persist after attempting these solutions, please contact Everbilt customer support.

Спецификације

Гаранција и подршка

For warranty information or technical support, please contact Everbilt customer service. Keep your purchase receipt as proof of purchase for any warranty claims.

За додатну помоћ, можете посетити Everbilt brand page on Amazon or consult the retailer where the product was purchased.