DS18 G1000.4D

DS18 G1000.4D Car Ampлифиер

Упутство за употребу

Модел: Г1000.4Д

Увод

Thank you for choosing the DS18 G1000.4D GEN-X Full-Range Class D 4-Channel Car Ampспасилац. Овај приручник пружа основне информације за правилну инсталацију, рад и одржавање вашег ampспасилац. Молимо вас да пажљиво прочитате ово упутство пре него што покушате да инсталирате или користите како бисте осигурали оптималне перформансе и безбедност.

Важне информације о безбедности

Садржај пакета

Кључне карактеристике

Спецификације

ФеатуреСпецификација
Број моделаГ1000.4Д
Излазна снага (макс.)1000 Ваттс
РМС снага @ 4 ома4 к 90В
РМС снага @ 2 ома4 к 150В
RMS Power Bridged @ 4 Ohms2 к 300В
Број канала4
Ampлифиер ЦлассКласа Д
Фреквенцијски одзив20Хз-20кХз
Однос сигнал-шум (СНР)>90 дБ
Укупна хармонијска дисторзија (ТХД)0.01%
Input Sensitivity (Low Level)0.25V - 6V
Инпут Импеданце22К Охмс
Dampинг Фактор78
Ефикасност @ 4 Охма92%
Димензије (Д к Ш к В)8.1 к 4.72 к 1.96 инча
Тежина артикла3.1 фунти
Волtage12 Волтс

Подешавање и инсталација

Правилна инсталација је кључна за перформансе и дуговечност вашег amplifier. If you are not confident in your ability to install this product, please consult a professional car audio installer.

Монтажа Ampлифиер

Choose a mounting location that is dry, well-ventilated, and protected from direct sunlight and excessive heat. Ensure there is sufficient airflow around the amplifier's heatsink. Secure the ampспасилац користећи приложени хардвер за монтажу.

DS18 G1000.4D Ampлифиер Топ View

Слика 1: Врх view of the DS18 G1000.4D amplifier, showing its compact design.

Ожичење

All wiring should be done with the vehicle's battery disconnected. Use high-quality wiring of appropriate gauge to minimize power loss and ensure safe operation.

Прикључци за напајање
DS18 G1000.4D Amplifier Power Input Terminals

Figure 2: Close-up of the power input terminals (GND, REM, +12V) and speaker output terminals on the DS18 G1000.4D ampлифиер.

Излазне везе звучника

Connect your speakers to the appropriate speaker output terminals. Ensure correct polarity (+ to + and - to -) for each speaker. Refer to the amplifier's specifications for minimum impedance requirements for stereo and bridged modes.

DS18 G1000.4D Amplifier Input and Output Connections

Слика 3: Завршеноview of the DS18 G1000.4D amplifier's input and output connections, including power, remote, ground, and speaker terminals.

Прикључци аудио улаза

The G1000.4D supports both low-level (RCA) and high-level inputs.

DS18 G1000.4D AmpУлазни и контролни панел за lifier

Figure 4: Close-up of the input and control panel, showing RCA inputs, high-level inputs, gain controls, and crossover switches.

Почетна подешавања

Before powering on, set the GAIN controls to minimum and the X-OVER switches to the desired setting (HPF, LPF, or FULL). Adjust these settings carefully after the system is powered on.

Unboxing and Internal View (Видео)

This video provides a detailed look at the DS18 G1000.4D amplifier, including its unboxing and an internal view of its components. This can be helpful for understanding the build quality and internal layout.

Video 1: DS18 G1000.4D Full Range Amplifier Unboxing and Internal Components Overview.

Упутство за употребу

Једном amplifier is properly installed and wired, you can begin adjusting its settings for optimal sound performance.

Подешавање појачања

The GAIN control matches the output of your head unit to the input sensitivity of the amplifier. Start with the gain at minimum. Play a familiar piece of music at about 75% of your head unit's maximum volume. Slowly increase the amplifier's gain until you hear distortion, then back off slightly. The CLIP indicator light can assist in this process, illuminating when the signal is clipping.

Цроссовер Сеттингс

The G1000.4D features adjustable High Pass Filter (HPF) and Low Pass Filter (LPF) for each channel pair (CH1/CH2 and CH3/CH4).

Adjust the crossover frequency according to your speaker types and desired sound. Typical settings for full-range speakers might be 80-120Hz HPF, while subwoofers would use an LPF in a similar range.

Одржавање

Your DS18 G1000.4D ampУређај за спасавање захтева минимално одржавање како би се осигурао дуготрајан рад.

Решавање проблема

Ако имате проблема са својим amplifier, refer to the following common issues and solutions:

ПроблемМогући узрокРешење
No Power / Protection Light OnBlown fuse, improper wiring, short circuit, overheating.Проверите уграђени осигурач и amplifier fuses. Verify power, ground, and remote connections. Check speaker wires for shorts. Ensure adequate ventilation.
Нема излаза звукаNo input signal, incorrect gain setting, speaker wiring error, head unit issue.Verify RCA or high-level input connections. Adjust gain. Check speaker wiring for correct polarity and secure connections. Test head unit with another ampспасилац ако је могуће.
Дистортед СоундGain set too high, improper crossover settings, speaker impedance mismatch, poor quality input signal.Reduce gain. Adjust crossover settings. Ensure speaker impedance matches amplifier's capabilities. Check input signal quality.
Бука / цвиљење мотораPoor grounding, RCA cables too close to power wires, faulty RCA cables, ground loop.Improve ground connection. Reroute RCA cables away from power wires. Try different RCA cables. Install a ground loop isolator if necessary.

Гаранција и подршка

Производи DS18 су дизајнирани и произведени по највишим стандардима квалитета. За конкретне услове гаранције, погледајте гарантни лист који је приложен уз ваш производ или посетите званичну веб страницу DS18. webсајт. Сачувајте рачун као доказ о куповини.

For technical support or service inquiries, please contact DS18 customer service through their official webсајту или овлашћеним дилерима.

Note: Unauthorized repairs or modifications will void the product warranty.