Упутство за употребу линеарног светла Stem Aria

Stem Aria Linear Light

ОПРЕЗ

ПРЕ УГРАДЊЕ

Please read the provided step-by-step instructions thoroughly before proceeding with the installation. You will achieve a secure and successful installation by taking these precautions and diligently following the provided guidelines.

1. Увек не заборавите да искључите напајање струјног кола пре него што започнете било какве радове на инсталацији. Послове електричне инсталације треба да обавља искључиво овлашћени електроинсталатер. За професионалне смернице, обратите се локалној служби за електричну енергију.
2. Пре уградње, проверите да ли у месту за инсталацију постоје други каблови како бисте спречили оштећење скривених ожичења.
3. When positioning the light fixture, ensure that the chosen area can adequately support the weight of light up to 3kg ( 6.6 lbs, aluminium)/ 7kg (15.4 lbs, brass).
4. Имајте на уму да је овај уређај дизајниран само за употребу у сувим кућним просторијама.
5. When handling the metal fixture, make sure your hands are clean. It is advised to wear gloves to prevent leaving marks on the metal surface.
6. Periodically check screws and connections for stability. Gently tighten if necessary, avoid over-tightening.

УПУТСТВА ЗА НЕГУ

Уверите се да су вам руке чисте пре него што додирнете металну површину да не бисте оставили трагове отисака прстију. Саветује се да користите рукавице при руковању расветним уређајем. Не користите никакве абразивне супстанце на производу. Обратите пажњу на његову тежину. Поступати са пажњом.

Over time, the metal surface may diminish its original luster. To retain the original aluminium or brass finish, use metal polish with a soft, dry cloth and gently rub it onto the surface.

ТЕХНИЧКИ ДЕТАЉИ

• Димензије
  • Dia.. 26 L1440 MM
  • Dia 1 L56.7 IN (Custom length on request)
• Материјал и тежина
  • Cast Aluminium – 2.5 kg
  • Cast Brass – 6 kg
• Келвинова оцена 3000K
• Извор светлости
  IND/ UK/ EU LED strip (Incl.)12W, 220-240V
• Classification IP20
• Фазно сечење које се може димирати, компатибилно са TRIAC-ом
• Хардвер
  W56 H32 D140 MM W2.2 H1.3 D5.5 IN Aluminium, Brass finish
• Цорд
  • Хардвире
  • Cord length – 2000 MM

УНУТРАШЊЕ КУТИЈЕ

* Driver and LED light are not included for regions with a voltagзахтев од 110-120V.

(Сл. 1)

КОРАК 1

Position and drill

Carefully mark the position where you intend for the light fixture to hang. Use the dimensions marked (Fig. 1) as a guide to drill holes in the ceiling, then proceed to the next step.

(Сл. 2)

КОРАК 2

Install the Clutch wire gripper and Canopy back plate

1. Connect the clutch wire gripper (A1) and canopy back plate (B) by fastening them at the drilled holes in the ceiling using the drywall screws (Fig. 3).
2. Insert the clutch wire (C) through the clutch wire screw (D)(Fig. 4), fitted on the ends of the cast Rod.
3. Secure the opposite end of the clutch wire gripper (A1)(Fig. 3).
   1. To ensure the safe suspension of the light fixture, check that the wires are firmly attached to the clutch wire grippers and are devoid of any slack.

(Сл. 5)

КОРАК 3

Install the second Clutch wire gripper

Take the second clutch wire gripper (A2) and fasten it directly onto the ceiling (Fig. 6) using the drywall screw. Now insert the clutch wire (C) through the clutch wire screw (D) (Fig. 4) and securely attach it to the clutch wire gripper (A2) (Fig. 6).

(Сл. 7)

КОРАК 4

Install and level the Rod

Fasten the clutch wire screw (D) to both ends of the Rod (Fig. 7) and adjust its height as desired. Ensure that the light fixture is in alignment with the floor.

(Сл. 8)

КОРАК 5

Connect the wiring to the driver

1. Insert the LED cord end (F) on the Rod through the hole in the canopy casing (E) and connect it to the driver output mounted on the ceiling (Fig. 8).
2. Connect the driver input to the electrical connection in the ceiling (Fig. 9).
   Ensure that all connections are secure and that there are no exposed wires or electrical hazards. Pay attention to the polarity of the connection. A wrong connection can cause damage.

(Сл. 10)

КОРАК 6

Close the Canopy casing

After completing the installation, take the canopy’s top cover and attach it to the back plate (Fig. 10) using the canopy screws (Fig. 11). Ensure that the wiring and any excess clutch wire strands are neatly trimmed after the installation.

In case you require further assistance, please write to us at info@stemdesign.co.

Често постављана питања