Улица М5СТЕКamp-S3Bat Embedded Core Module User Guide

Улица М5СТЕКamp-S3Bat Embedded Core Module

Опис

Stamp-S3Bat is an embedded core module integrated with power management. It utilizes the ESP32-S3-PICO-1-N8R8 as the main control core, supports 2.4GHz Wi-Fi, and comes with built-in 8MB Flash and 8MB PSRAM.
It provides 11 GPIO pins, an onboard battery power interface, and can be directly connected to an external 3.7V lithium battery for power supply.

With an efficient built-in PMIC and multi-level power control design, it supports power input and output control, as well as status monitoring for input voltagе и батерија волtage. It supports external low-power wake-up. After the main controller shuts down and enters low-power sleep mode, it can be triggered to wake up via an external PMIC wake-up IO. The module features an onboard user button and a programmable RGB LED. With 2.54mm standard-pitch half-hole solder pads, it can be integrated into your applications through SMT, DIP, or other methods, helping developers quickly build IoT applications.

Спецификације

Брзи почетак

Припрема

1. Посетите званични Ардуино webсајт и инсталирајте Ардуино ИДЕ
   https://www.arduino.cc/en/Main/Software
2. Додајте следећег менаџера одбора URL да File → Подешавања → Менаџер додатних табли URLs:
   https://espressif.github.io/arduino-esp32/package_esp32_dev_index.json
3. Отворите Boards Manager, потражите „ESP32“ и кликните на инсталирај.
4. After installation, select the board “ESP32S3 Dev Module”.
5. Configure the following options. USB CDC On Boot: “Enabled”, PSRAM： “OPI PSRAM”, USB Mode: “Hardware CDC and JTAG„

Ви-Фи Сцан

• Изаберите екampпрограм „Ex“amples” → “WiFi” → “WiFiScan”, choose the port corresponding to your device, and click the compile and upload button in the top-left corner.
• After uploading is complete, open the Serial Monitor to view Информације о скенирању Wi-Fi мреже.

БЛЕ Сцан

• Изаберите екampпрограм „Ex“amples” → “BLE” → ”Scan”, choose the port corresponding to your device, and click the compile and upload button in the top-left corner.
• After uploading is complete, open the Serial Monitor to view Информације о BLE скенирању.

Упозорење ФЦЦ

Упозорење ФЦЦ:
Све промене или модификације које није изричито одобрила страна одговорна за усклађеност могу поништити корисниково овлашћење да користи опрему.

Овај уређај је у складу са делом 15 ФЦЦ правила. Операција је подложна следећа два услова:

1. This device may not cause harmful interference, andThiss device must accept any interference received, including interference that may cause undesired operation.

ВАЖНА НАПОМЕНА:

Напомена: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, use,s and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Преусмерите или преместите пријемну антену.
• Повећајте размак између опреме и пријемника.
• Повежите опрему у утичницу на струјном колу различитом од оног на који је прикључен пријемник.
• За помоћ се обратите продавцу или искусном радио/ТВ техничару.

Изјава ФЦЦ о изложености радијацији:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated wita h minimum distance of 20cm between the radiator & your body.

Често постављана питања